"Can't Miss" Release Button Aids In Ultra-Fast Magazine Changes
Extended, drop-in replacement for factory part offers a wide, flat finger pad for fast, can t miss magazine changes. Perfect for competition, tactical operations, and self-defense any high-stress situation where the speed of a magazine change makes the difference between success and failure. Nearly three times the surface area of the factory button with crisp, 24 lpi checkering for positive, nonslip finger contact, so you release the mag on the very first try. Stands .225" higher to give you extra leverage that ensures the mag catch disengages completely. Precision machined from 4140 steel and heat treated for added hardness and wear resistance, with a tough, black oxide finish. May require minor fitting.
SPECS: Steel, oxide finish, matte black. Fits any AR-15/M16/CAR-15/M4 with a USGI-spec magazine release.
Mehr...
"Kann nicht verfehlen" Release-Button hilft bei ultra-schnellen Magazinwechseln
Erweiterter, einfach einsetzbarer Ersatz für das Originalteil bietet eine breite, flache Fingerauflage für schnelle, fehlerfreie Magazinwechsel. Perfekt für Wettkämpfe, taktische Einsätze und Selbstverteidigung in jeder stressigen Situation, in der die Geschwindigkeit eines Magazinwechsels den Unterschied zwischen Erfolg und Misserfolg ausmacht. Fast dreimal die Oberfläche des Originalknopfs mit präzisem, 24 lpi Rautenmuster für positiven, rutschfesten Fingerkontakt, sodass du das Magazin beim ersten Versuch loslassen kannst. Steht .225" höher, um dir zusätzlichen Hebel zu geben, der sicherstellt, dass der Magazinhalter vollständig entriegelt. Präzisionsgefertigt aus 4140 Stahl und wärmebehandelt für zusätzliche Härte und Verschleissfestigkeit, mit einer robusten, schwarzen Oxidbeschichtung. Möglicherweise ist eine geringfügige Anpassung erforderlich.
SPECS: Stahl, Oxidbeschichtung, matt schwarz. Passt auf jede AR-15/M16/CAR-15/M4 mit einem USGI-spezifizierten Magazinrelease.
Mehr...
Kundenbewertungen zu BROWNELLS OVERSIZED MAGAZINE RELEASE BUTTON
Anzahl der Bewertungen: 12
Von brownells.com: 12
Durchschnittliche Bewertung: 3.4
Good but not great(20.01.2010)
I purchased this item along with a larger order of items for my AR-15, and it was easy to install, but the fit was very loose. I didn't really like it after that so I am sending it back to Brownells. I will use that money for other great items from Brownells.
Brownells mag catch button(27.03.2010)
You must remove bolt catch to properly install this part or you can not screw it in far enough to keep the magazine catch from rotating up or down when you depress the button.
Buyer beware(24.12.2010)
Need to remove bolt catch to install. Even after removing bolt catch, it is too loose to rely on. If this is somthing you just got to have, I would suggest using a low grade locktite to prevent the catch side from dropping down when depressing the magazine release.
sticks out a country mile on sig556(16.05.2011)
maybe works better on AR-15s, but now I understand the two piece approach. The flanged top does not allow you to insert the release in far enough and still thread in the release latch. So its going to stick up very high regardless of the gun. I liked it because the head went so far to the rear which is what the SIG556 really needs.
Was also pretty loose in the slot.
Best with Norgon(08.09.2011)
Not meant for receivers with ambidextrous bolt catch. However, when paired with an ambidextrous (e.g., NORGON) magazine release lever, this huge button installs very easy and does not allow opposing lever to rotate when pressed. You'll never make a faster mag swap!
Must Buy!(09.04.2012)
I have put this on several AR's and will be buying more. Works great.
BIG improvement over stock part.(13.05.2012)
This is a very well made part that greatly improves your access to the mag release. It is easy to install, after you remove the bolt catch, a minor inconvenience. Put one on my Colt H-Bar Match and my Rock River Predator Pursuit.
Sticks out a little too far(05.10.2012)
I have not had any functional problems with it at all, it works just fine. This would be an excellent product if they would re-engineer it so that it did not stick out so far. I understand that it is supposed to be oversize, but did not expect it to stick out as far as it does. Installed in a Mega billet lower if that helps anyone.
Great button(30.09.2013)
Even though I live in CA my guns are pre ban and registered so I can legally have them. This mag release works GREAT! I now have them on 3 of my AR's and have had no problems with fit, function, or appearance. Even with my short fingers it is right there for fast mag changes in competition.
A well made part but...(16.10.2014)
This safety button is very well made and finished but due to as listed below, it will be returned.
1-It sticks out too far and would snag on everything.
2- It is a very loose fit in the $230.00 billet lower that my customer is having me build.
3- the design allows for the mag catch itself to get out of its mortice if the button is pressed in all the way. That would not let the gun retain the magazine and defeat the purpose of the mag catch in the first place. My customer said no way!! It will be returned to Brownells under their famous satisfaction guarantee.
Not bad but could be easily improved.(30.10.2014)
Overall I like it. Again a design issue arises. This is designed to enhance or lengthen the magazine release button. It may be an assumption however I think buyers are looking for the additional length to be rearward. It is lengthened rearward but is also lengthened forward for reasons unknown to me. I know I read about concerns of the button being caught on clothing or a sling or other object because the enhancement makes an area that can catch on things. Not being able to depress the magazine release and allowing the magazine to be changed could be a problem.....you think? Adding another frontal area for that potential problem seems to be unnecessary. Hey just my observations. Sometimes less is more.
Over sized Mag Release(10.10.2017)
Looks good,,well made,I'm not fitting it to any of my guns as one other reviewer states ...
"the design allows for the mag catch itself to get out of its mortice if the button is pressed in all the way" This is going to be a real problem hunting and in competitive shooting.
Artikel-Nr.: 080000529 BROWNELLS OVERSIZED MAGAZINE RELEASE BUTTON050806109377 Erweiterter, einfach einsetzbarer Ersatz für das Originalteil bietet eine breite, flache Fingerauflage für schnelle, fehlerfreie Magazinwechsel. Perfekt für Wettkämpfe, taktische Einsätze und Selbstverteidigung in jeder stressigen Situation, in der die Geschwindigkeit eines Magazinwechsels den Unterschied zwischen Erfolg und Misserfolg ausmacht. Fast dreimal die Oberfläche des Originalknopfs mit präzisem, 24 lpi Rautenmuster für positiven, rutschfesten Fingerkontakt, sodass du das Magazin beim ersten Versuch loslassen kannst. Steht .225" höher, um dir zusätzlichen Hebel zu geben, der sicherstellt, dass der Magazinhalter vollständig entriegelt. Präzisionsgefertigt aus 4140 Stahl und wärmebehandelt für zusätzliche Härte und Verschleissfestigkeit, mit einer robusten, schwarzen Oxidbeschichtung. Möglicherweise ist eine geringfügige Anpassung erforderlich.
39.9CHF0CHF 39.90
*
Nachbestellt, Lieferzeit ca. 4-12 Wochen aus dem Lager USA.
Made in USA
US-Exportklassifizierung: 0A501.x
Dieses Produkt unterliegt der Aufsicht der Regierung der Vereinigten Staaten von Amerika und ist ausschliesslich für den Export in das Bestimmungsland zur Verwendung durch den endgültigen Empfänger oder Endverbraucher, der beim Kauf festgelegt wird, bestimmt. Dieses Produkt darf ohne vorherige Erlaubnis der Regierung der Vereinigten Staaten von Amerika oder einer autorisierten US-Behörde über den endgültigen Empfänger oder Endverbrauchers hinaus nicht wiederverkauft, übertragen, oder in einer anderen Weise in Drittländer oder an Dritte überlassen werden. Dies gilt auch dann, wenn die Artikel verbaut bzw. in einen anderen Artikel integriert wurde.
This item is controlled by the U.S. government and authorized for export only to the country of ultimate destination for use by the ultimate consignee or end-user(s) herein identified. It may not be resold, transferred, or otherwise disposed of, to any other country or to any person other than the authorized ultimate consignee or end-user(s), either in their original form or after being incorporated into other items, without first obtaining approval from the U.S. government or as otherwise authorized by U.S. law and regulations.
Upgrade deinen AR-15 mit dem OVERSIZED MAGAZINE RELEASE BUTTON von BROWNELLS! 🛠️ Schnelle Magazinwechsel und präzise Verarbeitung für jede Situation.
"Can't Miss" Release Button Aids In Ultra-Fast Magazine Changes
Extended, drop-in replacement for factory part offers a wide, flat finger pad for fast, can t miss magazine changes. Perfect for competition, tactical operations, and self-defense any high-stress situation where the speed of a magazine change makes the difference between success and failure. Nearly three times the surface area of the factory button with crisp, 24 lpi checkering for positive, nonslip finger contact, so you release the mag on the very first try. Stands .225" higher to give you extra leverage that ensures the mag catch disengages completely. Precision machined from 4140 steel and heat treated for added hardness and wear resistance, with a tough, black oxide finish. May require minor fitting.
SPECS: Steel, oxide finish, matte black. Fits any AR-15/M16/CAR-15/M4 with a USGI-spec magazine release.
Mehr...
"Kann nicht verfehlen" Release-Button hilft bei ultra-schnellen Magazinwechseln
Erweiterter, einfach einsetzbarer Ersatz für das Originalteil bietet eine breite, flache Fingerauflage für schnelle, fehlerfreie Magazinwechsel. Perfekt für Wettkämpfe, taktische Einsätze und Selbstverteidigung in jeder stressigen Situation, in der die Geschwindigkeit eines Magazinwechsels den Unterschied zwischen Erfolg und Misserfolg ausmacht. Fast dreimal die Oberfläche des Originalknopfs mit präzisem, 24 lpi Rautenmuster für positiven, rutschfesten Fingerkontakt, sodass du das Magazin beim ersten Versuch loslassen kannst. Steht .225" höher, um dir zusätzlichen Hebel zu geben, der sicherstellt, dass der Magazinhalter vollständig entriegelt. Präzisionsgefertigt aus 4140 Stahl und wärmebehandelt für zusätzliche Härte und Verschleissfestigkeit, mit einer robusten, schwarzen Oxidbeschichtung. Möglicherweise ist eine geringfügige Anpassung erforderlich.
SPECS: Stahl, Oxidbeschichtung, matt schwarz. Passt auf jede AR-15/M16/CAR-15/M4 mit einem USGI-spezifizierten Magazinrelease.
Mehr...
Kundenbewertungen zu BROWNELLS OVERSIZED MAGAZINE RELEASE BUTTON
Anzahl der Bewertungen: 12
Von brownells.com: 12
Durchschnittliche Bewertung: 3.4
Good but not great(20.01.2010)
I purchased this item along with a larger order of items for my AR-15, and it was easy to install, but the fit was very loose. I didn't really like it after that so I am sending it back to Brownells. I will use that money for other great items from Brownells.
Brownells mag catch button(27.03.2010)
You must remove bolt catch to properly install this part or you can not screw it in far enough to keep the magazine catch from rotating up or down when you depress the button.
Buyer beware(24.12.2010)
Need to remove bolt catch to install. Even after removing bolt catch, it is too loose to rely on. If this is somthing you just got to have, I would suggest using a low grade locktite to prevent the catch side from dropping down when depressing the magazine release.
sticks out a country mile on sig556(16.05.2011)
maybe works better on AR-15s, but now I understand the two piece approach. The flanged top does not allow you to insert the release in far enough and still thread in the release latch. So its going to stick up very high regardless of the gun. I liked it because the head went so far to the rear which is what the SIG556 really needs.
Was also pretty loose in the slot.
Best with Norgon(08.09.2011)
Not meant for receivers with ambidextrous bolt catch. However, when paired with an ambidextrous (e.g., NORGON) magazine release lever, this huge button installs very easy and does not allow opposing lever to rotate when pressed. You'll never make a faster mag swap!
Must Buy!(09.04.2012)
I have put this on several AR's and will be buying more. Works great.
BIG improvement over stock part.(13.05.2012)
This is a very well made part that greatly improves your access to the mag release. It is easy to install, after you remove the bolt catch, a minor inconvenience. Put one on my Colt H-Bar Match and my Rock River Predator Pursuit.
Sticks out a little too far(05.10.2012)
I have not had any functional problems with it at all, it works just fine. This would be an excellent product if they would re-engineer it so that it did not stick out so far. I understand that it is supposed to be oversize, but did not expect it to stick out as far as it does. Installed in a Mega billet lower if that helps anyone.
Great button(30.09.2013)
Even though I live in CA my guns are pre ban and registered so I can legally have them. This mag release works GREAT! I now have them on 3 of my AR's and have had no problems with fit, function, or appearance. Even with my short fingers it is right there for fast mag changes in competition.
A well made part but...(16.10.2014)
This safety button is very well made and finished but due to as listed below, it will be returned.
1-It sticks out too far and would snag on everything.
2- It is a very loose fit in the $230.00 billet lower that my customer is having me build.
3- the design allows for the mag catch itself to get out of its mortice if the button is pressed in all the way. That would not let the gun retain the magazine and defeat the purpose of the mag catch in the first place. My customer said no way!! It will be returned to Brownells under their famous satisfaction guarantee.
Not bad but could be easily improved.(30.10.2014)
Overall I like it. Again a design issue arises. This is designed to enhance or lengthen the magazine release button. It may be an assumption however I think buyers are looking for the additional length to be rearward. It is lengthened rearward but is also lengthened forward for reasons unknown to me. I know I read about concerns of the button being caught on clothing or a sling or other object because the enhancement makes an area that can catch on things. Not being able to depress the magazine release and allowing the magazine to be changed could be a problem.....you think? Adding another frontal area for that potential problem seems to be unnecessary. Hey just my observations. Sometimes less is more.
Over sized Mag Release(10.10.2017)
Looks good,,well made,I'm not fitting it to any of my guns as one other reviewer states ...
"the design allows for the mag catch itself to get out of its mortice if the button is pressed in all the way" This is going to be a real problem hunting and in competitive shooting.