Forster makes a collet style bullet puller for standard seven eigths thru 14 threaded presses and a second collet style puller (both use the same Forster collets) for the Co-Ax Press. The FBP1010 puller for standard presses includes a collet tightening handle on top of the puller body. The FUP1010 Puller has a nine sixteenths inch hex top on the puller body which requires a wrench to tighten the collet. Both pullers easily remove bullets from almost any cartridge. Collets are sold separately.
Mehr...
Forster bietet einen Collet-Stil Bullet Puller für Standardpressen mit einem Gewinde von sieben Achtel bis 14 an und einen zweiten Collet-Stil Puller (beide verwenden die gleichen Forster Collets) für die Co-Ax Press. Der FBP1010 Puller für Standardpressen hat einen Collet-Ziehgriff oben am Puller-Gehäuse. Der FUP1010 Puller hat einen Sechzehntel Zoll Sechskant oben am Puller-Gehäuse, der einen Schlüssel zum Festziehen des Collets benötigt. Beide Puller entfernen problemlos Geschosse aus fast jeder Patrone. Collets werden separat verkauft.
Mehr...
Kundenbewertungen zu FORSTER PRODUCTS, INC. UNIVERSAL BULLET PULLER, COLLETS NOT INCLUDED
Anzahl der Bewertungen: 3
Von brownells.com: 3
Durchschnittliche Bewertung: 2.7
Disapointing design(29.01.2012)
I purchased the puller from Sinclair along with three collets, thereby saving money rather than Forster dirctly. The puller I chose was the "Universal" with the hex head as in pic. The hex head is a soft metal nut, thread glued on a minor thread. On the second cartridge (6.5 x 55), the thread lock gave up and the hex head /nut, turned on its own. I am now left with no option but to use padded vice grips to extract the "collet screw body. Why not use a one piece "bolt". Remember the principle of KISS, less to go wrong. The quality of the collets however is high, but the "gripping force" exerted inside the puller by a tapering surface could be better finished, probably such tightening force was required. I would have gone for the Hornady Cam Lock, but, I don`t believe you can cover two calibers with one collet, 6.5/.264 & .257 Also, from Forsters I purchased a dozen pack of die lock rings. I was very disapointed to find them to be soft alloy. Now I happily find Sinclair do their own lock rings in stainless, well done.
Sent it back - would not buy again(15.06.2012)
Not up to the usual Forster quality. The collect nut is held on by lock-tite and came un-screwed on the tenth bullet I pulled. Do not waste your money.
Revised!(29.01.2015)
Product has been revised and now has an allen set screw that appears to be deep enough to seat into (or past) the threads of the collet pusher assembly. No way for the nut to turn now. Simple fix that should have been there from the beginning..., but live and learn. Buy with confidence, especially if you have a Forster Co-Ax press.
Artikel-Nr.: 749002538 FORSTER PRODUCTS, INC. UNIVERSAL BULLET PULLER, COLLETS NOT INCLUDED Herstellerproduktnummer: UP1010757253996863 Forster bietet einen Collet-Stil Bullet Puller für Standardpressen mit einem Gewinde von sieben Achtel bis 14 an und einen zweiten Collet-Stil Puller (beide verwenden die gleichen Forster Collets) für die Co-Ax Press. Der FBP1010 Puller für Standardpressen hat einen Collet-Ziehgriff oben am Puller-Gehäuse. Der FUP1010 Puller hat einen Sechzehntel Zoll Sechskant oben am Puller-Gehäuse, der einen Schlüssel zum Festziehen des Collets benötigt. Beide Puller entfernen problemlos Geschosse aus fast jeder Patrone. Collets werden separat verkauft.
Forster makes a collet style bullet puller for standard seven eigths thru 14 threaded presses and a second collet style puller (both use the same Forster collets) for the Co-Ax Press. The FBP1010 puller for standard presses includes a collet tightening handle on top of the puller body. The FUP1010 Puller has a nine sixteenths inch hex top on the puller body which requires a wrench to tighten the collet. Both pullers easily remove bullets from almost any cartridge. Collets are sold separately.
Mehr...
Forster bietet einen Collet-Stil Bullet Puller für Standardpressen mit einem Gewinde von sieben Achtel bis 14 an und einen zweiten Collet-Stil Puller (beide verwenden die gleichen Forster Collets) für die Co-Ax Press. Der FBP1010 Puller für Standardpressen hat einen Collet-Ziehgriff oben am Puller-Gehäuse. Der FUP1010 Puller hat einen Sechzehntel Zoll Sechskant oben am Puller-Gehäuse, der einen Schlüssel zum Festziehen des Collets benötigt. Beide Puller entfernen problemlos Geschosse aus fast jeder Patrone. Collets werden separat verkauft.
Mehr...
Kundenbewertungen zu FORSTER PRODUCTS, INC. UNIVERSAL BULLET PULLER, COLLETS NOT INCLUDED
Anzahl der Bewertungen: 3
Von brownells.com: 3
Durchschnittliche Bewertung: 2.7
Disapointing design(29.01.2012)
I purchased the puller from Sinclair along with three collets, thereby saving money rather than Forster dirctly. The puller I chose was the "Universal" with the hex head as in pic. The hex head is a soft metal nut, thread glued on a minor thread. On the second cartridge (6.5 x 55), the thread lock gave up and the hex head /nut, turned on its own. I am now left with no option but to use padded vice grips to extract the "collet screw body. Why not use a one piece "bolt". Remember the principle of KISS, less to go wrong. The quality of the collets however is high, but the "gripping force" exerted inside the puller by a tapering surface could be better finished, probably such tightening force was required. I would have gone for the Hornady Cam Lock, but, I don`t believe you can cover two calibers with one collet, 6.5/.264 & .257 Also, from Forsters I purchased a dozen pack of die lock rings. I was very disapointed to find them to be soft alloy. Now I happily find Sinclair do their own lock rings in stainless, well done.
Sent it back - would not buy again(15.06.2012)
Not up to the usual Forster quality. The collect nut is held on by lock-tite and came un-screwed on the tenth bullet I pulled. Do not waste your money.
Revised!(29.01.2015)
Product has been revised and now has an allen set screw that appears to be deep enough to seat into (or past) the threads of the collet pusher assembly. No way for the nut to turn now. Simple fix that should have been there from the beginning..., but live and learn. Buy with confidence, especially if you have a Forster Co-Ax press.