ADVANCED TECHNOLOGY
HEAT SHIELD

758152513007 019000004

Improves Control & Handling Convenience

Furnished with a complete set of adapters and spacers for installation on 12 gauge Mossberg 500, Maverick 88, Remington 870, and Winchester 1200/1300 pump shotguns. Easy to install, requires no modifications to firearm. Formed steel with elongated cooling slots protects your hands from burns. Provides a secure, non-slip, grasping surface, plus maximum heat dissipation. Simply slide over barrel and secure with supplied hardware. Black oxide finish matches most shotgun finishes. No gunsmithing required to fit most popular 12 gauge pump guns.

SPECS: Steel, black oxide, matte finish. 13¾ (35cm) long.

Mehr...

Verbessert Kontrolle & Handhabungskomfort

Geliefert mit einem kompletten Satz von Adaptern und Abstandshaltern für die Installation auf 12 Gauge Mossberg 500, Maverick 88, Remington 870 und Winchester 1200/1300 Pump-Action-Schrotflinten. Einfach zu installieren, keine Änderungen an der Feuerwaffe erforderlich. Geformter Stahl mit verlängerten Kühlöffnungen schützt deine Hände vor Verbrennungen. Bietet eine sichere, rutschfeste Grifffläche sowie maximale Wärmeableitung. Einfach über den Lauf schieben und mit der mitgelieferten Hardware sichern. Die schwarze Oxidbeschichtung passt zu den meisten Schrotflintenoberflächen. Kein Gunsmithing erforderlich, um die gängigsten 12 Gauge Pumpguns anzupassen.

SPECS: Stahl, schwarze Oxidbeschichtung, matte Oberfläche. 13¾ (35cm) lang.

Mehr...

Kundenbewertungen zu ADVANCED TECHNOLOGY HEAT SHIELD

Anzahl der Bewertungen: 6
Von brownells.com: 6
Durchschnittliche Bewertung: 3.2

Solid Piece of Gear (16.09.2009)

Installed the Heat Shield on my Rem 870 in about 10 minutes and it fit with no alterations to the shield or the shotgun. Well constructed with an excellent pattern for heat dispersion. I would buy it again.

IVE BOUGHT A FEW OF THESE (13.04.2010)

IF YOU SHOOT A LOT OF SHELLS AND HAVE EVER BURNED YOUR HAND BY ACCIDENTALLY TOUCHING THE BARREL THIS ITEM IS FOR YOU. IT INSTALLS EASILY AND QUICKLY AND DOESN'T NEED TO BE REMOVED WHEN YOU CLEAN THE BORE OR BREAK DOWN YOUR SHOTGUN. IT ALSO ADDS A TOUGH LOOK TO THE SHOTGUN. IVE ONLY INSTALLED THIS ON MOSSBERG 500'S AND HAVE HAD NO PROBLEMS.

Difficult to install (21.01.2011)

Quality parts and manufacturing, but tricky to install on my 870 Tactical. Took some extra bending of the middle tabs and widening of the receiver-end of the shield to fit snug around my barrel. Had to file down the upper inside edge of the fore-end, as well, as the middle tabs were grinding on it upon cycling the action.

SHS-1300 Heat Shield by Advanced Technol (12.08.2011)

its plastic it belongs on my suns toy gun not on a tactical home protection shot gun, When i picked up my shot gun after i had installed the heat shield,the back of the heat shield came off of my shot gun due to the ring on the back of the heat shield is not a solid ring and it is flimsy and moves around on my shot gun. I do not recommend this product if you are serious about home defense or self protection. i recommend one made of steel.

1300 defender (05.03.2012)

*this may not apply to all shotguns* The fit and finish of the product is unacceptable. During install the heat shield heavily scratches the barrel's finish. The receiver end of the shield does not grip the barrel well allowing it to move and produce wear on the barrel. The forward end, with the two screw holes, comes to you flared out and out of alignment. This neccesitates a lot of test fits and alterations which again damages the finish of the gun. A gunsmith might have better luck with it. Mine found its way into the dumpster.

A good buy (25.01.2014)

This was an easy install, it is not a custom piece built specific to any gun, it is built to fit every 870 ever made. Take your time and you won't damage the finish on your weapon or on the heat shield. The instructions are pretty clear and easily followed (I read them afterwards) no modification was required to my weapon (H&R Pardner Protector Pump) even though I installed an 870 wood stock and forearm and a +2 magazine extension. The heat shield does require a little patience for a good tight fit but looks good after installation. It is a great deal for quality and looks, especially because it it metal and cost the same as some synthetic models

Lesen Sie 6 weitere Bewertungen bei brownells.com

49.9 49.9 1 CHF

Artikel-Nr.: 019000004
ADVANCED TECHNOLOGY HEAT SHIELD
Herstellerproduktnummer: SHS1300 758152513007 Geliefert mit einem kompletten Satz von Adaptern und Abstandshaltern für die Installation auf 12 Gauge Mossberg 500, Maverick 88, Remington 870 und Winchester 1200/1300 Pump-Action-Schrotflinten. Einfach zu installieren, keine Änderungen an der Feuerwaffe erforderlich. Geformter Stahl mit verlängerten Kühlöffnungen schützt deine Hände vor Verbrennungen. Bietet eine sichere, rutschfeste Grifffläche sowie maximale Wärmeableitung. Einfach über den Lauf schieben und mit der mitgelieferten Hardware sichern. Die schwarze Oxidbeschichtung passt zu den meisten Schrotflintenoberflächen. Kein Gunsmithing erforderlich, um die gängigsten 12 Gauge Pumpguns anzupassen.

49.9 CHF 123 CHF 49.90 *

Lieferzeit ca. 8-15 Tage aus dem Lager USA.

Eigenschaften: Hersteller/Modell: Mossberg, Winchester, Remington, Maverick Modell: 870, 500, 1300, 1200, 88

Auf die Wunschliste setzen

Frage stellen

Details

Auf die Wunschliste setzen

Frage stellen

Top Takeaways

Einfach zu installieren mit einem kompletten Set von Adaptern für 12 Gauge Pump-Action-Schrotflinten.
Geformter Stahl mit Kühlöffnungen schützt deine Hände vor Verbrennungen und sorgt für eine rutschfeste Griffoberfläche.
Schwarze Oxidbeschichtung passt zu den meisten Schrotflintenoberflächen und erfordert kein Gunsmithing.

Eigenschaften

Hersteller/Modell: Maverick,Mossberg,Remington,Winchester Modell: 1200,1300,500,870,88 Versandgewicht: 0.249kg Versandhöhe: 30mm Versandbreite: 51mm Versandlänge: 467mm UPC : 758152513007