Distributes recoil on heavy magnums. Heavy-walled tube goes inside the stock, secures between two bolts with specially designed heads. With sharp, squared edges for clean inletting. Finish to match stock contours.
Verteilt den Rückstoss bei schweren Magnum-Kalibern. Das dickwandige Rohr wird im Schaft platziert und zwischen zwei Schrauben mit speziell gestalteten Köpfen gesichert. Mit scharfen, quadratischen Kanten für eine saubere Einpassung. Oberfläche passend zu den Konturen des Schafts.
SPECS: Rohr ¼" (6.3mm) Durchmesser, 1-3⁄8" (3.5cm) lang. Köpfe 7⁄16" (11.1mm) Durchmesser, 1⁄8" (3.2mm) dick. Bearbeitetes Stahl, in der Rohform.
Mehr...
Kundenbewertungen zu TALLEY MAGNUM CROSSBOLT
Anzahl der Bewertungen: 5
Von brownells.com: 5
Durchschnittliche Bewertung: 4
A Little Disappointed(28.12.2009)
I was unable to use the product. I was attempting a stock repair using techniques that I was unfamiliar with, and I thought this product would fill the bill.
The product itself looks to be a pretty good one.
My problem was that I also bought the MAUSER Cross Bolt Wrench, thinking that it would work for this product. I found nothing in the catalogue that explained that this product requires a different tool.
Lesson learned. I recommend adding a comment in the catalog indicating what the correct tool would be for tightening it down, and that the MAUSER Cross Bolt Wrench is intended for MAUSER Cross Bolts ONLY.
Great Value(26.02.2010)
I was pleased with the quality and low cost. You will need a 1/4" drill, a 7/16" counterbore with 1/4" pilot to machine the stock. Strongly recommend doing this work in a milling machine. Did not see a spanner wrench to fit this crossbolt, so I made a simple T-handle spanner out of 7/16" round stock. Drilled the spanner pins at 9/32" (.2812) and made the pins out of .075 pin stock.
Just what I needed!(14.10.2010)
I purchased this product to repace a missing rear crossbolt on a Russian SKS rifle. It's a perfect fit, though I might need to thin the head a little.
As for the proper tool to use, I was able to a the cheap SKS crossbolt tool. They're typically sold by a number of folks, but not Brownells.
great to use(24.11.2010)
Very good product. I have fitted these in cliets stocks. Works just as well as the K98 cross bolts. Its just a shame they don't do them in stainless steel aswell. If you havent got the right tool to fit them, then "C" clip pliers work well.
Dandy(26.06.2017)
Several comments regarding lack of a wrench available. This does not use the Mauser wrench. However stop by the auto parts store with a cross bolt and you will find a pair of snap ring pliers work quite well.
Artikel-Nr.: 874005000 TALLEY MAGNUM CROSSBOLT Herstellerproduktnummer: CB876430004983 Verteilt den Rückstoss bei schweren Magnum-Kalibern. Das dickwandige Rohr wird im Schaft platziert und zwischen zwei Schrauben mit speziell gestalteten Köpfen gesichert. Mit scharfen, quadratischen Kanten für eine saubere Einpassung. Oberfläche passend zu den Konturen des Schafts.
Made in USA
US-Exportklassifizierung: 0A501.x
Dieses Produkt unterliegt der Aufsicht der Regierung der Vereinigten Staaten von Amerika und ist ausschliesslich für den Export in das Bestimmungsland zur Verwendung durch den endgültigen Empfänger oder Endverbraucher, der beim Kauf festgelegt wird, bestimmt. Dieses Produkt darf ohne vorherige Erlaubnis der Regierung der Vereinigten Staaten von Amerika oder einer autorisierten US-Behörde über den endgültigen Empfänger oder Endverbrauchers hinaus nicht wiederverkauft, übertragen, oder in einer anderen Weise in Drittländer oder an Dritte überlassen werden. Dies gilt auch dann, wenn die Artikel verbaut bzw. in einen anderen Artikel integriert wurde.
This item is controlled by the U.S. government and authorized for export only to the country of ultimate destination for use by the ultimate consignee or end-user(s) herein identified. It may not be resold, transferred, or otherwise disposed of, to any other country or to any person other than the authorized ultimate consignee or end-user(s), either in their original form or after being incorporated into other items, without first obtaining approval from the U.S. government or as otherwise authorized by U.S. law and regulations.
Entdecke den MAGNUM CROSSBOLT von TALLEY! 🎯 Ideal für Magnum-Kaliber, verteilt den Rückstoss optimal und sorgt für perfekte Passform.
Distributes recoil on heavy magnums. Heavy-walled tube goes inside the stock, secures between two bolts with specially designed heads. With sharp, squared edges for clean inletting. Finish to match stock contours.
Verteilt den Rückstoss bei schweren Magnum-Kalibern. Das dickwandige Rohr wird im Schaft platziert und zwischen zwei Schrauben mit speziell gestalteten Köpfen gesichert. Mit scharfen, quadratischen Kanten für eine saubere Einpassung. Oberfläche passend zu den Konturen des Schafts.
SPECS: Rohr ¼" (6.3mm) Durchmesser, 1-3⁄8" (3.5cm) lang. Köpfe 7⁄16" (11.1mm) Durchmesser, 1⁄8" (3.2mm) dick. Bearbeitetes Stahl, in der Rohform.
Mehr...
Kundenbewertungen zu TALLEY MAGNUM CROSSBOLT
Anzahl der Bewertungen: 5
Von brownells.com: 5
Durchschnittliche Bewertung: 4
A Little Disappointed(28.12.2009)
I was unable to use the product. I was attempting a stock repair using techniques that I was unfamiliar with, and I thought this product would fill the bill.
The product itself looks to be a pretty good one.
My problem was that I also bought the MAUSER Cross Bolt Wrench, thinking that it would work for this product. I found nothing in the catalogue that explained that this product requires a different tool.
Lesson learned. I recommend adding a comment in the catalog indicating what the correct tool would be for tightening it down, and that the MAUSER Cross Bolt Wrench is intended for MAUSER Cross Bolts ONLY.
Great Value(26.02.2010)
I was pleased with the quality and low cost. You will need a 1/4" drill, a 7/16" counterbore with 1/4" pilot to machine the stock. Strongly recommend doing this work in a milling machine. Did not see a spanner wrench to fit this crossbolt, so I made a simple T-handle spanner out of 7/16" round stock. Drilled the spanner pins at 9/32" (.2812) and made the pins out of .075 pin stock.
Just what I needed!(14.10.2010)
I purchased this product to repace a missing rear crossbolt on a Russian SKS rifle. It's a perfect fit, though I might need to thin the head a little.
As for the proper tool to use, I was able to a the cheap SKS crossbolt tool. They're typically sold by a number of folks, but not Brownells.
great to use(24.11.2010)
Very good product. I have fitted these in cliets stocks. Works just as well as the K98 cross bolts. Its just a shame they don't do them in stainless steel aswell. If you havent got the right tool to fit them, then "C" clip pliers work well.
Dandy(26.06.2017)
Several comments regarding lack of a wrench available. This does not use the Mauser wrench. However stop by the auto parts store with a cross bolt and you will find a pair of snap ring pliers work quite well.