Trims The Rivet Tip To Make Broken Ejector Spring Removal Simple
Hollow-end mill fits in drill press, spot faces the front rivet to take off just the peened area. Often lets you re-peen the existing rivet and eliminate rebluing the receiver.
Schneidet die Nietspitze, um das Entfernen der defekten Auswerferfeder zu erleichtern
Der Hohl-Endfräser passt in die Bohrmaschine und bearbeitet den vorderen Niet, um nur den umgebogenen Bereich zu entfernen. Oft kannst du den vorhandenen Niet wieder umbiegen und das Neulackieren des Empfängers vermeiden.
Kundenbewertungen zu BROWNELLS REMINGTON 870 EJECTOR SPRING RIVET CUTTER
Anzahl der Bewertungen: 1
Von brownells.com: 1
Durchschnittliche Bewertung: 5
Great investment!(10.02.2016)
This little rivet cutter made me save over $200 in gunsmithing work on my old 870 Wingmaster, which had been sitting in the gun safe for years because of a ''too-expensive-to-replace'' broken ejector spring. The instructions provided with the tool are very clear and allowed me, as indicated, to re-use the rivet to lock the new spring into the ejector. The only thing I did differently than prescribed by the instructions was to drive the rivet cutter down on the tiny rivet head by hand instead of using a press drill. The rivet cutter being very sharp and the rivet metal being very soft, I was afraid to ruin the rivet using a press drill. It took me 10 minutes to cut the rivet head slowly and safely by hand (clockwise twist of the fingers with little pressure).
Artikel-Nr.: 080000040 BROWNELLS REMINGTON 870 EJECTOR SPRING RIVET CUTTER050806103825 Der Hohl-Endfräser passt in die Bohrmaschine und bearbeitet den vorderen Niet, um nur den umgebogenen Bereich zu entfernen. Oft kannst du den vorhandenen Niet wieder umbiegen und das Neulackieren des Empfängers vermeiden.
54.9CHF0CHF 54.90
*
Nachbestellt, Lieferzeit ca. 4-12 Wochen aus dem Lager USA.
Trims The Rivet Tip To Make Broken Ejector Spring Removal Simple
Hollow-end mill fits in drill press, spot faces the front rivet to take off just the peened area. Often lets you re-peen the existing rivet and eliminate rebluing the receiver.
Schneidet die Nietspitze, um das Entfernen der defekten Auswerferfeder zu erleichtern
Der Hohl-Endfräser passt in die Bohrmaschine und bearbeitet den vorderen Niet, um nur den umgebogenen Bereich zu entfernen. Oft kannst du den vorhandenen Niet wieder umbiegen und das Neulackieren des Empfängers vermeiden.
Kundenbewertungen zu BROWNELLS REMINGTON 870 EJECTOR SPRING RIVET CUTTER
Anzahl der Bewertungen: 1
Von brownells.com: 1
Durchschnittliche Bewertung: 5
Great investment!(10.02.2016)
This little rivet cutter made me save over $200 in gunsmithing work on my old 870 Wingmaster, which had been sitting in the gun safe for years because of a ''too-expensive-to-replace'' broken ejector spring. The instructions provided with the tool are very clear and allowed me, as indicated, to re-use the rivet to lock the new spring into the ejector. The only thing I did differently than prescribed by the instructions was to drive the rivet cutter down on the tiny rivet head by hand instead of using a press drill. The rivet cutter being very sharp and the rivet metal being very soft, I was afraid to ruin the rivet using a press drill. It took me 10 minutes to cut the rivet head slowly and safely by hand (clockwise twist of the fingers with little pressure).