NECG
RUGER 77/22™ GHOST RING RECEIVER REAR SIGHT

661040100

Clamps Quickly To Ruger Integral Bases

Finely machined steel receiver sight clamps to factory dovetail on Ruger® rifles; serves as an excellent primary hunting sight in situations where a scope may not be practical. Carry in your pack as an emergency sight to save your hunt in case of scope failure. Install and remove without loss of zero. Height matches most M-77®, 77/22® and #1 factory front sights. Includes .093" and .125" apertures that draw your eye to the sight for fast sight alignment. Adjustable for windage and elevation.

SPECS: Steel, blue finish. 1-1/4" (3.2cm) long. 3/4" (19mm) high. 1-1/4" (3.2cm) wide.

Plus...

Se fixe rapidement aux bases intégrées Ruger

Ce viseur arrière en acier finement usiné se fixe sur le dovetail d'origine des carabines Ruger® ; il constitue un excellent viseur de chasse principal dans des situations où une lunette peut ne pas être pratique. Emporte-le dans ton sac comme un viseur d'urgence pour sauver ta chasse en cas de défaillance de la lunette. Installe-le et retire-le sans perte de réglage. La hauteur correspond à la plupart des viseurs avant d'origine M-77®, 77/22® et #1. Comprend des ouvertures de .093" et .125" qui attirent ton œil vers le viseur pour un alignement rapide. Réglable en dérive et en élévation.

CARACTÉRISTIQUES : Acier, finition bleue. Longueur de 1-1/4" (3,2 cm). Hauteur de 3/4" (19 mm). Largeur de 1-1/4" (3,2 cm).

Plus...

Évaluations client de NECG RUGER 77/22 PEEP GHOST RING RECEIVER REAR SIGHT BLACK

Nombre d'évaluations: 5
De brownells.com: 5
Note moyenne: 3.4

Buyer Beware (31.05.2010)

Difficult to adjust. You will go thru alot of ammo. The metal prong that goes into Ruger sight mounts will only allow it to go so far to left or right. Recently I took one off my Ruger International and it rusted and damaged my rifle sight mounts. Contacted NECG twice and they failed to communicate.

Good product [...] (19.10.2010)

I bought this sight for my Ruger Mk II RSI. [...] but I was sad to find that it didn't fit. The tab on the sight was too thick to fit into the slot in the receiver by about .010". [...]Once at the range, I really liked how it performed. The targets are much harder to see than with a scope, but not so much harder to hit! This sight is a nice compliment to a short, handy rifle like the RSI.The windage and elevation adjustments do not have any "clicks" to them, and the windage doesn't even have any markings. It seemed like the elevation changed slightly as I adjusted the windage (the windage adjustment essentially just scoots the sight left and right on the receiver, so you're essentially removing it every time you adjust windage). Despite this, it didn't take me too long to get it zeroed.So far, my factory front sight is working just fine. I may get a different blade from NECG just to tighten up my groups at the range, but the fairly-big brass "dot" blade from Ruger should be great for deer hunting.[...]Click adjustments would be nice, but not required. All in all, a good product.

Not a drop in part! (25.04.2011)

The tab on the base of the sight was a bit too thick. It required disassembly of the sight and a whisker of filing to get it to drop into the corresponding slot in the receiver. This sight would have be a simple drop in part if the tab had been slightly thinner. Other than that It was exactly what I was looking for and I really didn't mind spending the few minutes to fit it.

An excellent apeture sight (01.09.2012)

Good design, very well made. Easy to adjust windage and elevation. Bought for a Ruger 77/44 and fits and adjusts as advertised (NB. can't use rear-most ring mount position as it will foul the bolt). Only issue is limited windage range due to extension in Ruger cross-slot limiting lateral adjustment. Solution - drift the front sight to compensate. An excellent robust, low-profile peep sight.

Good sight / Requires taller front sight (07.04.2014)

I installed this sight on an older 77/22. It shot extremely high with the original front sight. I installed a .530 Marbles front sight and it still shot 6" high at 50 yards. Next I installed a .570 Marbles front, this brought it to 2" high at 50 yards. I know all rifles shoot a little different this seems to be excessive to me. Be prepared to change front sights if you put this on a 77/22.

Lire 5 plus d'avis sur brownells.com

154.9 154.9 1 CHF

Référence: 661040100
NECG RUGER 77/22 PEEP GHOST RING RECEIVER REAR SIGHT BLACK
Ref Fabricant: N-100 Ce viseur arrière en acier finement usiné se fixe sur le dovetail d'origine des carabines Ruger® ; il constitue un excellent viseur de chasse principal dans des situations où une lunette peut ne pas être pratique. Emporte-le dans ton sac comme un viseur d'urgence pour sauver ta chasse en cas de défaillance de la lunette. Installe-le et retire-le sans perte de réglage. La hauteur correspond à la plupart des viseurs avant d'origine M-77®, 77/22® et #1. Comprend des ouvertures de .093" et .125" qui attirent ton œil vers le viseur pour un alignement rapide. Réglable en dérive et en élévation.

154.9 CHF 0 CHF 154.90 *

En rupture de stock, délai de livraison d'environ 4-12 semaines depuis l'entrepôt des États-Unis.

Caractéristiques: Couleur: Noir Manufacture: Ruger Modèle: 77/22 Style: Peep

Ajouter à la Liste d'Envies

Poser un question

Propriétés

Ajouter à la Liste d'Envies

Poser un question

Points forts

Le viseur arrière se fixe facilement au rail d'usine des carabines Ruger®.
Idéal comme viseur d'urgence, il s'installe et se retire sans perte de zéro.
Réglable en dérive et en élévation, avec des ouvertures pour un alignement rapide.

Caractéristiques

Couleur: Noir Manufacture: Ruger Modèle: 77/22 Style: Peep Poids du colis: 0.068kg Hauteur d'expédition: 10mm Largeur d'expédition: 81mm Longueur d'expédition: 147mm