Three, reduced power springs for tuning and smoothing felt trigger pull. Fits the newer P220, P226 and P229's that use a short mainspring with a plastic, hammer spring base insert. Contains 1 each of 17, 18, and 19 lb., reduced power, mainsprings. P220 factory spring is 22 lb. P226 and P229 factory spring is 24 lb.
Mehr...
Reduziert den Abzug, verbessert die Genauigkeit
Drei reduzierte Federn zur Feinabstimmung und Glättung des gefühlten Abzugs. Passt zu den neueren P220, P226 und P229, die eine kurze Hauptfeder mit einem Kunststoffeinsatz für die Schlagfeder verwenden. Enthält je eine Feder mit 17, 18 und 19 lb, reduzierte Leistung, Hauptfedern. Die Werkseinstellung der P220-Feder beträgt 22 lb. Die Werkseinstellung der P226 und P229-Feder beträgt 24 lb.
Mehr...
Kundenbewertungen zu WOLFF SIG MAINSPRING KIT #32356
Anzahl der Bewertungen: 4
Von brownells.com: 4
Durchschnittliche Bewertung: 4.5
Wolff Sig Mainspring(11.07.2009)
Been using these to custom tune triggers on 226 9mm's for several years. As a stand alone part and replacement, it is ok but far from perfect. It does make for a slightly smoother pull, but is best used in conjunction with some polishing work, and Wolff Firing Pin Springs in order to custom tune the firing pin inertia and give you a reliable impact on the primer. If you don't, you may find some FTF/Light Strikes on hard primers found in a lot of Military/Surplus ammunition.
Easy to use for the garage gunsmith to give a slightly better pull, best used by a legitimate gunsmith for a truly significant improvement.
Works as advertised(23.03.2010)
I have been working on Sig pistols for over 10 years and have used these reduced power springs to improve trigger pulls for some time now and never had a single problem. They work as intended/adverised.
WOLFF SIG MAINSPRING KIT(06.05.2012)
This kit provides you with the proper spring for your special needs and all will reduce the trigger pull in DA and SA. A lot of parts polishing will make it smooth and the spring does the rest. I have always been able to get 100% ignition with the 17lbs spring but recommend a little heavier for a duty or self defense gun.
Works great(21.05.2017)
These reduced power mainsprings do as described. I'm currently using the 18lb spring as I had light primer strikes on CCI primers with the 17lb one. Next time I disassemble my slide, I'll replaced the factory firing pin spring with a reduced power one and retry the 17lb spring.
DA is down to approx 9lbs and SA is a crisp 3.5lbs.
Artikel-Nr.: 969000021 WOLFF SIG MAINSPRING KIT #32356 Herstellerproduktnummer: 32356 Drei reduzierte Federn zur Feinabstimmung und Glättung des gefühlten Abzugs. Passt zu den neueren P220, P226 und P229, die eine kurze Hauptfeder mit einem Kunststoffeinsatz für die Schlagfeder verwenden. Enthält je eine Feder mit 17, 18 und 19 lb, reduzierte Leistung, Hauptfedern. Die Werkseinstellung der P220-Feder beträgt 22 lb. Die Werkseinstellung der P226 und P229-Feder beträgt 24 lb.
26.9CHF16CHF 26.90
*
Lieferzeit ca. 8-15 Tage aus dem Lager USA.
Eigenschaften:Hersteller/Modell: Sig SauerModell: P226
Three, reduced power springs for tuning and smoothing felt trigger pull. Fits the newer P220, P226 and P229's that use a short mainspring with a plastic, hammer spring base insert. Contains 1 each of 17, 18, and 19 lb., reduced power, mainsprings. P220 factory spring is 22 lb. P226 and P229 factory spring is 24 lb.
Mehr...
Reduziert den Abzug, verbessert die Genauigkeit
Drei reduzierte Federn zur Feinabstimmung und Glättung des gefühlten Abzugs. Passt zu den neueren P220, P226 und P229, die eine kurze Hauptfeder mit einem Kunststoffeinsatz für die Schlagfeder verwenden. Enthält je eine Feder mit 17, 18 und 19 lb, reduzierte Leistung, Hauptfedern. Die Werkseinstellung der P220-Feder beträgt 22 lb. Die Werkseinstellung der P226 und P229-Feder beträgt 24 lb.
Mehr...
Kundenbewertungen zu WOLFF SIG MAINSPRING KIT #32356
Anzahl der Bewertungen: 4
Von brownells.com: 4
Durchschnittliche Bewertung: 4.5
Wolff Sig Mainspring(11.07.2009)
Been using these to custom tune triggers on 226 9mm's for several years. As a stand alone part and replacement, it is ok but far from perfect. It does make for a slightly smoother pull, but is best used in conjunction with some polishing work, and Wolff Firing Pin Springs in order to custom tune the firing pin inertia and give you a reliable impact on the primer. If you don't, you may find some FTF/Light Strikes on hard primers found in a lot of Military/Surplus ammunition.
Easy to use for the garage gunsmith to give a slightly better pull, best used by a legitimate gunsmith for a truly significant improvement.
Works as advertised(23.03.2010)
I have been working on Sig pistols for over 10 years and have used these reduced power springs to improve trigger pulls for some time now and never had a single problem. They work as intended/adverised.
WOLFF SIG MAINSPRING KIT(06.05.2012)
This kit provides you with the proper spring for your special needs and all will reduce the trigger pull in DA and SA. A lot of parts polishing will make it smooth and the spring does the rest. I have always been able to get 100% ignition with the 17lbs spring but recommend a little heavier for a duty or self defense gun.
Works great(21.05.2017)
These reduced power mainsprings do as described. I'm currently using the 18lb spring as I had light primer strikes on CCI primers with the 17lb one. Next time I disassemble my slide, I'll replaced the factory firing pin spring with a reduced power one and retry the 17lb spring.
DA is down to approx 9lbs and SA is a crisp 3.5lbs.