No-Mar Brass Rod Knocks Stuck Bullets Out Of Bores
Don't let a stuck bullet from a "squib" or weak load cut short a shooting session. Far superior to other rods or makeshift punches, this non-marring brass rod fits the bore closely, can't wedge between bullet nose and rifling. Each rod is drilled and tapped to thread onto a Dewey cleaning rod; very handy for knocking stuck bullets out of rifle barrels.
SPECS: Kit contains one of each size rod and (2) 8-32 to 12-28 adapters. 8" (20.3cm) long. Brass. Pak has 2 rods of size listed and 2 Dewey 30A rod adapters.
Mehr...
Nicht markierender Messingstab entfernt feststeckende Geschosse aus Läufen
Lass dich nicht von einer feststeckenden Patrone durch einen "squib" oder schwachen Ladevorgang die Schiesssession verderben. Weitaus überlegen gegenüber anderen Stäben oder improvisierten Stösseln, passt dieser nicht markierende Messingstab eng in den Lauf und kann sich nicht zwischen Geschossnase und Züge klemmen. Jeder Stab ist gebohrt und gewindegefertigt, um auf einen Dewey-Reinigungsstab geschraubt zu werden; sehr praktisch, um feststeckende Geschosse aus Gewehrläufen zu entfernen.
SPECS: Das Kit enthält je einen Stab jeder Grösse und (2) 8-32 zu 12-28 Adaptern. 8" (20.3cm) lang. Messing. Das Paket enthält 2 Stäbe der angegebenen Grösse und 2 Dewey 30A Stabadapter.
Mehr...
Kundenbewertungen zu BROWNELLS 45 CALIBER SQUIB ROD 8" LONG 2 PACK
Anzahl der Bewertungen: 7
Von brownells.com: 7
Durchschnittliche Bewertung: 3.3
Saved my Model 10(31.05.2010)
Got out my progressive press after a few years and loaded up some wadcutters. Went out to the range to test them. After a few rounds, my gun locked up. I could see a bullet lodged between the cylinder and the forcing cone. Took the gun home and got out my squib rod kit. Followed the directions, took out the mainspring and hammer. I measured the the squib rod in the barrel and them tapped it with a plastic hammer. A few taps later, the cylinder opened and I was able to remove the cartridge and bullet. It appears there was no powder, just a primer in this one; a hazard of using a progressive. Saved me a trip to the gunsmith. If you shoot more than one caliber, buy the whole kit. "Be prepared."
fits and works(04.04.2016)
These fit and work well. You need one of these in your tools and range bag.
Can't fit a 40SW barrel(05.08.2013)
It is too tight and can't fit any of my 40SW STI barrels.
Too big.(04.04.2016)
I returned a set that were too big to go down the barrel with a comment on the appropriate diameter. The replacement set is also too big.
In order to fit easily down the barrel they should be .385, plus or minus. .389 is apparently the absolute max diameter to fit inside the rifling. The first set was .392. The second set was .390.
Somebody's tolerances are not being checked.
Don't Buy(11.05.2016)
This is the third set of .40 squib rods that will not work. They will just fit down a Glock barrel but will not fit down a .40 S&W M/P barrel (tried it in multiple different pistols). If you really want them, plan on turning them down yourself to a diameter that works in your pistol.
Squibb Rod Is Essential Safety Tool(25.09.2012)
I use the Brownell's Squibb Rod Kit often in my duties as a range safety officer to clear bore obstructions and to dislodge stuck cases.
A bullet stuck in the bore, caused by inadvertently loading and attempting to fire a round with primer-only and no powder can be a serious hazard if not properly handled. A few drops of Kroil down the bore quickly reduce adhesion of a stuck jacketed bullet with the bore. The appropriate size squibb rod and adapter are threaded onto the Dewey cleaning rod and the obstruction tapped out the breech by multiple light taps of the rod only. No hammer is needed.
Occasionally you experience a stuck case in an AR which cannot be removed by pulling the charging handle. With the muzzle pointed in a safe direction, and the breech cover open, place the squibb rod against the bolt carrier and rap with a mallet to drive the bolt carrier to the rear, unlocking the bolt so that the jammed round or case can be removed safely.
A bullet-in-bore malfunction in a revolver often jams the cylinder, so that it cannnot be opened. A wrap with the squibb rod quickly and easily drives the stuck bullet back into the cylinder, clear of the forcing cone, so that the range can be declared clear.
To determine the proper size of cast bullet to load in an antique military or cowboy rifle it is necesssary to upset a throat "slug" to measure the diameter of the forcing cone ahead of the chamber. This is done by filling a sized case up to its mouth with molten lead from the casting pot, then filing the lead flush. Chamber an inch long piece of bore-diameter, soft, pure-lead wire in from of the lead-filled case, and use the Brownell squibb rod to upset the slug so that it conforms to the forcing cone and throat. Knock out the upset slug with a fired case from your rifle to send to the mold maker.
A must have if you like to shoot!(11.03.2013)
I purchased this set a little while back. I have had 2 squibs(1-45, 1-40) since and they were factory loads. No tool box should be without them. They work PERFECT, easy to use, already paid for itself. THANKS!
Artikel-Nr.: 084175045 BROWNELLS 45 CALIBER SQUIB ROD 8" LONG 2 PACK Herstellerproduktnummer: 45SQUIBROD050806031395 Lass dich nicht von einer feststeckenden Patrone durch einen "squib" oder schwachen Ladevorgang die Schiesssession verderben. Weitaus überlegen gegenüber anderen Stäben oder improvisierten Stösseln, passt dieser nicht markierende Messingstab eng in den Lauf und kann sich nicht zwischen Geschossnase und Züge klemmen. Jeder Stab ist gebohrt und gewindegefertigt, um auf einen Dewey-Reinigungsstab geschraubt zu werden; sehr praktisch, um feststeckende Geschosse aus Gewehrläufen zu entfernen.
54.9CHF0CHF 54.90
*
Nachbestellt, Lieferzeit ca. 4-12 Wochen aus dem Lager USA.
No-Mar Brass Rod Knocks Stuck Bullets Out Of Bores
Don't let a stuck bullet from a "squib" or weak load cut short a shooting session. Far superior to other rods or makeshift punches, this non-marring brass rod fits the bore closely, can't wedge between bullet nose and rifling. Each rod is drilled and tapped to thread onto a Dewey cleaning rod; very handy for knocking stuck bullets out of rifle barrels.
SPECS: Kit contains one of each size rod and (2) 8-32 to 12-28 adapters. 8" (20.3cm) long. Brass. Pak has 2 rods of size listed and 2 Dewey 30A rod adapters.
Mehr...
Nicht markierender Messingstab entfernt feststeckende Geschosse aus Läufen
Lass dich nicht von einer feststeckenden Patrone durch einen "squib" oder schwachen Ladevorgang die Schiesssession verderben. Weitaus überlegen gegenüber anderen Stäben oder improvisierten Stösseln, passt dieser nicht markierende Messingstab eng in den Lauf und kann sich nicht zwischen Geschossnase und Züge klemmen. Jeder Stab ist gebohrt und gewindegefertigt, um auf einen Dewey-Reinigungsstab geschraubt zu werden; sehr praktisch, um feststeckende Geschosse aus Gewehrläufen zu entfernen.
SPECS: Das Kit enthält je einen Stab jeder Grösse und (2) 8-32 zu 12-28 Adaptern. 8" (20.3cm) lang. Messing. Das Paket enthält 2 Stäbe der angegebenen Grösse und 2 Dewey 30A Stabadapter.
Mehr...
Kundenbewertungen zu BROWNELLS 45 CALIBER SQUIB ROD 8" LONG 2 PACK
Anzahl der Bewertungen: 7
Von brownells.com: 7
Durchschnittliche Bewertung: 3.3
Saved my Model 10(31.05.2010)
Got out my progressive press after a few years and loaded up some wadcutters. Went out to the range to test them. After a few rounds, my gun locked up. I could see a bullet lodged between the cylinder and the forcing cone. Took the gun home and got out my squib rod kit. Followed the directions, took out the mainspring and hammer. I measured the the squib rod in the barrel and them tapped it with a plastic hammer. A few taps later, the cylinder opened and I was able to remove the cartridge and bullet. It appears there was no powder, just a primer in this one; a hazard of using a progressive. Saved me a trip to the gunsmith. If you shoot more than one caliber, buy the whole kit. "Be prepared."
fits and works(04.04.2016)
These fit and work well. You need one of these in your tools and range bag.
Can't fit a 40SW barrel(05.08.2013)
It is too tight and can't fit any of my 40SW STI barrels.
Too big.(04.04.2016)
I returned a set that were too big to go down the barrel with a comment on the appropriate diameter. The replacement set is also too big.
In order to fit easily down the barrel they should be .385, plus or minus. .389 is apparently the absolute max diameter to fit inside the rifling. The first set was .392. The second set was .390.
Somebody's tolerances are not being checked.
Don't Buy(11.05.2016)
This is the third set of .40 squib rods that will not work. They will just fit down a Glock barrel but will not fit down a .40 S&W M/P barrel (tried it in multiple different pistols). If you really want them, plan on turning them down yourself to a diameter that works in your pistol.
Squibb Rod Is Essential Safety Tool(25.09.2012)
I use the Brownell's Squibb Rod Kit often in my duties as a range safety officer to clear bore obstructions and to dislodge stuck cases.
A bullet stuck in the bore, caused by inadvertently loading and attempting to fire a round with primer-only and no powder can be a serious hazard if not properly handled. A few drops of Kroil down the bore quickly reduce adhesion of a stuck jacketed bullet with the bore. The appropriate size squibb rod and adapter are threaded onto the Dewey cleaning rod and the obstruction tapped out the breech by multiple light taps of the rod only. No hammer is needed.
Occasionally you experience a stuck case in an AR which cannot be removed by pulling the charging handle. With the muzzle pointed in a safe direction, and the breech cover open, place the squibb rod against the bolt carrier and rap with a mallet to drive the bolt carrier to the rear, unlocking the bolt so that the jammed round or case can be removed safely.
A bullet-in-bore malfunction in a revolver often jams the cylinder, so that it cannnot be opened. A wrap with the squibb rod quickly and easily drives the stuck bullet back into the cylinder, clear of the forcing cone, so that the range can be declared clear.
To determine the proper size of cast bullet to load in an antique military or cowboy rifle it is necesssary to upset a throat "slug" to measure the diameter of the forcing cone ahead of the chamber. This is done by filling a sized case up to its mouth with molten lead from the casting pot, then filing the lead flush. Chamber an inch long piece of bore-diameter, soft, pure-lead wire in from of the lead-filled case, and use the Brownell squibb rod to upset the slug so that it conforms to the forcing cone and throat. Knock out the upset slug with a fired case from your rifle to send to the mold maker.
A must have if you like to shoot!(11.03.2013)
I purchased this set a little while back. I have had 2 squibs(1-45, 1-40) since and they were factory loads. No tool box should be without them. They work PERFECT, easy to use, already paid for itself. THANKS!