Designed for AmeriGlo by well-known M&P customizer David Bowie for a sleek, ultra-low-profile fit on the Smith & Wesson M&P pistol. The rear sight notch is wider and deeper than the factory notch to help you get the front sight centered ASAP. Rounded corners prevent snagging that can impair the draw from concealment.
SPECS: Machined steel, matte black finish. Tritium Front - .435" (11.1mm) long, .140" (3.6mm) wide, .230" (5.8mm) high. Target Front - .400" (10.2mm) long, .140" wide, .230" high. Tritium & Target Rear (All) - .875" (22.2mm) long, .720" (18.3mm) wide rear face, .235" (6mm) overall height above slide, .164" x .115" notch. Tritium sets available with green front/green rear sight (G/G) or green front/yellow rear (G/Y).*Fits all models except Pro Series and "L" versions.
Mehr...
Niedrigprofil-Kampfsicht
Entwickelt für AmeriGlo von dem bekannten M&P-Anpasser David Bowie für eine schlanke, ultra-flache Passform auf der Smith & Wesson M&P Pistole. Der Ausschnitt des Hintervisiers ist breiter und tiefer als der Werkausschnitt, um dir zu helfen, das Vordervisier so schnell wie möglich zu zentrieren. Abgerundete Ecken verhindern das Hängenbleiben, was das Ziehen aus der Verdeckung beeinträchtigen kann.
SPECS: Aus maschinellem Stahl, matte schwarze Oberfläche. Tritium Front - .435" (11.1mm) lang, .140" (3.6mm) breit, .230" (5.8mm) hoch. Target Front - .400" (10.2mm) lang, .140" breit, .230" hoch. Tritium & Target Rear (Alle) - .875" (22.2mm) lang, .720" (18.3mm) breite Rückseite, .235" (6mm) Gesamthöhe über dem Schlitten, .164" x .115" Ausschnitt. Tritium-Sets sind mit grünem Vorder-/grünem Hintervisier (G/G) oder grünem Vorder-/gelbem Hintervisier (G/Y) erhältlich.*Passt auf alle Modelle ausser Pro Series und "L" Versionen.
Mehr...
Kundenbewertungen zu AMERIGLO S&W M&P GREEN/GREEN SIGHT SET
Anzahl der Bewertungen: 3
Von brownells.com: 3
Durchschnittliche Bewertung: 4.7
Great M&P9 Night Sights(30.01.2012)
Installed these on my M&P9 full-size. The sights are well made and I was able to get them sighted in perfectly. Nice and bright. Used a sight pusher to install them and it was simple to do.
ALL THAT I WANTED(26.08.2012)
ADDED TO MY S&W M&P 9MM NIGHT STAND WEAPON. TOOK 20 MINUTES AT MY KITCHEN COUNTER, NO VISE OR CLAMPS; USED LIGHT HAMMER, 5/16 BRASS PUNCH AND REAR SIGHT TOOL ($4.00) THIS IS NEEDED TO KEEP SPRING FROM POPPING. OILED EXISTING SIGHTS LOOSENED REAR SET SCREW AND TAPPED OUT SIGHT INSERTING SIGHT TOOL HALFWAY. SAME WITH FRONT, REVERSE PROCEEDURE WITH NEW SIGHTS AND ENJOY
Very Nice Night Sights(06.12.2012)
I picked up a NIB M&P Shield 9mm in a trade recently and decided it needed some night sights since it will be one of my carry guns. After looking at all of the options, I decided on these due to the price point and the styling of the rear sight.
They arrived today and installation was easy enough. Neither the rear nor the front sight needed any fitting. The rear slid in by hand, which is fine since it has the set screw to hold it in place anyway. I felt that the front sight was a little too easy to tap in, so I removed it and added a little loctite under it to make sure it doesn't move under recoil. It probably didn't need it, but I wanted to be sure.
The rear sight didn't really hang over the edge of the slide, but due to the narrower slide on the Shield, the "contour" didn't really match up with the slide. It would in no way affect function, but I took a small file and reshaped the profile of the rear sight (in the area of the dovetail, not the sighting portion) to make it match the slide better. A bluing pen touched up the filed area just fine.
For reference, the front sight is actually finished black much like the factory sights and slide, but the rear sight is more gray, and the bluing pen matched very well. Someone would have to inspect closely to even be able to tell that I did anything to the rear sight.
I have not tested for POI yet, but comparing with the height of the factory sights, this set should do just fine.
The sights are VERY visible in both daylight, low light, and pitch black conditions.
Artikel-Nr.: 100004565 AMERIGLO S&W M&P GREEN/GREEN SIGHT SET Herstellerproduktnummer: SW-801644409017476 Entwickelt für AmeriGlo von dem bekannten M&P-Anpasser David Bowie für eine schlanke, ultra-flache Passform auf der Smith & Wesson M&P Pistole. Der Ausschnitt des Hintervisiers ist breiter und tiefer als der Werkausschnitt, um dir zu helfen, das Vordervisier so schnell wie möglich zu zentrieren. Abgerundete Ecken verhindern das Hängenbleiben, was das Ziehen aus der Verdeckung beeinträchtigen kann.
134.9CHF2CHF 134.90
*
Lieferzeit ca. 8-15 Tage aus dem Lager USA.
Eigenschaften:Art: Low-Profile, Night Sight, 3-Dot, TritiumFarbe der Visierung: Green/GreenHersteller/Modell: Smith & WessonModell: M&P
Designed for AmeriGlo by well-known M&P customizer David Bowie for a sleek, ultra-low-profile fit on the Smith & Wesson M&P pistol. The rear sight notch is wider and deeper than the factory notch to help you get the front sight centered ASAP. Rounded corners prevent snagging that can impair the draw from concealment.
SPECS: Machined steel, matte black finish. Tritium Front - .435" (11.1mm) long, .140" (3.6mm) wide, .230" (5.8mm) high. Target Front - .400" (10.2mm) long, .140" wide, .230" high. Tritium & Target Rear (All) - .875" (22.2mm) long, .720" (18.3mm) wide rear face, .235" (6mm) overall height above slide, .164" x .115" notch. Tritium sets available with green front/green rear sight (G/G) or green front/yellow rear (G/Y).*Fits all models except Pro Series and "L" versions.
Mehr...
Niedrigprofil-Kampfsicht
Entwickelt für AmeriGlo von dem bekannten M&P-Anpasser David Bowie für eine schlanke, ultra-flache Passform auf der Smith & Wesson M&P Pistole. Der Ausschnitt des Hintervisiers ist breiter und tiefer als der Werkausschnitt, um dir zu helfen, das Vordervisier so schnell wie möglich zu zentrieren. Abgerundete Ecken verhindern das Hängenbleiben, was das Ziehen aus der Verdeckung beeinträchtigen kann.
SPECS: Aus maschinellem Stahl, matte schwarze Oberfläche. Tritium Front - .435" (11.1mm) lang, .140" (3.6mm) breit, .230" (5.8mm) hoch. Target Front - .400" (10.2mm) lang, .140" breit, .230" hoch. Tritium & Target Rear (Alle) - .875" (22.2mm) lang, .720" (18.3mm) breite Rückseite, .235" (6mm) Gesamthöhe über dem Schlitten, .164" x .115" Ausschnitt. Tritium-Sets sind mit grünem Vorder-/grünem Hintervisier (G/G) oder grünem Vorder-/gelbem Hintervisier (G/Y) erhältlich.*Passt auf alle Modelle ausser Pro Series und "L" Versionen.
Mehr...
Kundenbewertungen zu AMERIGLO S&W M&P GREEN/GREEN SIGHT SET
Anzahl der Bewertungen: 3
Von brownells.com: 3
Durchschnittliche Bewertung: 4.7
Great M&P9 Night Sights(30.01.2012)
Installed these on my M&P9 full-size. The sights are well made and I was able to get them sighted in perfectly. Nice and bright. Used a sight pusher to install them and it was simple to do.
ALL THAT I WANTED(26.08.2012)
ADDED TO MY S&W M&P 9MM NIGHT STAND WEAPON. TOOK 20 MINUTES AT MY KITCHEN COUNTER, NO VISE OR CLAMPS; USED LIGHT HAMMER, 5/16 BRASS PUNCH AND REAR SIGHT TOOL ($4.00) THIS IS NEEDED TO KEEP SPRING FROM POPPING. OILED EXISTING SIGHTS LOOSENED REAR SET SCREW AND TAPPED OUT SIGHT INSERTING SIGHT TOOL HALFWAY. SAME WITH FRONT, REVERSE PROCEEDURE WITH NEW SIGHTS AND ENJOY
Very Nice Night Sights(06.12.2012)
I picked up a NIB M&P Shield 9mm in a trade recently and decided it needed some night sights since it will be one of my carry guns. After looking at all of the options, I decided on these due to the price point and the styling of the rear sight.
They arrived today and installation was easy enough. Neither the rear nor the front sight needed any fitting. The rear slid in by hand, which is fine since it has the set screw to hold it in place anyway. I felt that the front sight was a little too easy to tap in, so I removed it and added a little loctite under it to make sure it doesn't move under recoil. It probably didn't need it, but I wanted to be sure.
The rear sight didn't really hang over the edge of the slide, but due to the narrower slide on the Shield, the "contour" didn't really match up with the slide. It would in no way affect function, but I took a small file and reshaped the profile of the rear sight (in the area of the dovetail, not the sighting portion) to make it match the slide better. A bluing pen touched up the filed area just fine.
For reference, the front sight is actually finished black much like the factory sights and slide, but the rear sight is more gray, and the bluing pen matched very well. Someone would have to inspect closely to even be able to tell that I did anything to the rear sight.
I have not tested for POI yet, but comparing with the height of the factory sights, this set should do just fine.
The sights are VERY visible in both daylight, low light, and pitch black conditions.