Ihr Warenkorb ist leer.

Warenkorb

Hilfe und Kontakt

Versandkostenfreie Lieferung ab 399 CHF

100-tägiges Rückgaberecht

Newsletter

Angebote

Über 300.000 Kunden - wir sagen Danke!

4,93/5 "Sehr gut" (1400+ Bewertungen)

40,000+ Produkte aus Jagd und Schiesssport

TPS PRODUCTS
TSR PICATINNY SCOPE RINGS

071611307017 100020389

Super Holding Power, Precision Alignment

TSR Series Rings, precisely machined from an aluminum billet, with tolerances held to .0002", give maximum scope/ring contact. Holds scope securely against recoil. Four-screw cap lets you align the reticle, tighten the left side of the cap, then the right side without the scope rotating. Radiused edges and corners help prevent snagging while providing attractive appearance. Large, clamp-nut lets you torque rings to Mil-STD 1913 (Picatinny) bases.

SPECS: 7075-T651 Aluminum Alloy, matte black, hard anodized to Mil-A-8625 standards. 5/8" (15.8mm) wide. Height measured from top of base to center of ring. 30mm - High: 1.225" (31.1mm).

Mehr...

Super Haltekraft, Präzise Ausrichtung

Die TSR-Serie Ringe sind präzise aus einem Aluminiumblock gefräst, mit Toleranzen von .0002", was maximalen Kontakt zwischen Zielfernrohr und Ring gewährleistet. Hält das Zielfernrohr sicher gegen Rückstoss. Der Vier-Schrauben-Kappen ermöglicht es dir, das Absehen auszurichten, die linke Seite der Kappe festzuziehen und dann die rechte Seite, ohne dass sich das Zielfernrohr dreht. Abgerundete Kanten und Ecken helfen, Hängenbleiben zu vermeiden und sorgen für ein attraktives Aussehen. Die grosse Klemmmutter ermöglicht es dir, die Ringe an Mil-STD 1913 (Picatinny) Basen anzuziehen.

SPECS: 7075-T651 Aluminiumlegierung, matt schwarz, hart eloxiert nach Mil-A-8625 Standards. 5/8" (15,8mm) breit. Höhe gemessen von der Oberseite der Basis bis zur Mitte des Rings. 30mm - Hoch: 1.225" (31,1mm).

Mehr...

Kundenbewertungen zu TPS PRODUCTS 35MM MEDIUM (1.185") STEEL RINGS

Anzahl der Bewertungen: 25
Von brownells.com: 25
Durchschnittliche Bewertung: 4.6

Great Rings (16.04.2010)

Mounted these rings on a brand new Savage model 12FCV 22-250 and I couldn't be happier. They were recomended by a gunsmith buddy and he was right. No lapping required. Didn't have to adjust the scope much at all to get it sighted in because it was aligned so well. Don't waste your money on the big name rings and basis. Save that for the glass and rifle.

Great value, but not tall enough for AR (11.05.2011)

The quality of these rings is excellent. Great value here. These are very comparable to Leupold tactical rings at a much lower price. I got these for a flat top AR varmint rig to mount my VX3 4.5-14 X 50 30mm Long Range. These rings are rock solid. Gun spends everyday bouncing in feedtruck, but stays spot-on. These rings ARE NOT tall enough for this set-up. Just wish they came 1/4 in. taller. In the proper set-up, you'll be very satisfied. Five star item, but need to specify on a "tactical style" ring set that they will NOT work on an AR.

Height seems fine (20.03.2012)

Not sure what to add to the other reviews. Put this on a AR platform built in .450 with a Leupold 30mm scope. The "high" size lines up just right for me with a Rock River Arms stock. They seem to be holding just fine and the guns shoots 1" at 100.

Solid performer (18.09.2012)

This is my second set of these aluminum tactical rings from TPS. They are very solidly built, easily installed and perfectly square. I set up AR's for tactical competition, these rings have been perfect. Have had no problems with removing scope and remounting, holding point of aim every time. I would recommend these stout well built rings as best value.

Great rings (28.11.2011)

For the money these are the best rings you can get. I have them on three of my bolt guns and one of my AR-15's. TPS mounts are great too.

Best value rings I have used (06.03.2012)

These were recommended by a friend and he was correct. Excellent value for money.

Better than the rest (08.01.2010)

These are top of the line rings, they are better due to their quality control. There is no need to lap them like with badger. and the price is half of what you'd pay for .

Outstanding Quality (16.03.2015)

I highly recommend these rings.

The quality is equal to another set that I paid twice as much for. They are very solid, have an excellent finish, and mounted perfectly. I am very happy with them.

Excellent Rings (23.11.2009)

This is my second set of TPS/TSR rings. They come with detailed instructions. The finish and quality are very good. The high rings worked great for me mounted on an AR-15.

Great product (12.12.2009)

High quality, rugged, and good looking.

Best rings for the money (08.01.2010)

These have got to be the best rings for the money. I have 3 different sets of these along with several sets of Leupold Mark 4 rings. They are just as sturdy and well built at the Leupolds. I am very impressed with them and recommend them to all.

Exceptional (17.12.2010)

These rings allowed me to mount a 50mm scope on a PRI "tube". The threaded portion of the shaft allows for positive mounting. The instructions are very detailed and should be followed.

A Great Value In A Tactical Ring (21.06.2009)

These rings are precisely machined and have an excellent, uniform finish. The upper and lower ring components are indexed during installation and allow for slight variations in scope diameters. The torx ring screws and picatinny mounting bolt are rock solid and stay put under recoil. If you are looking for a high quality aluminum tactical ring, the TSR is a great value.

Excellent Robust Rings (30.08.2010)

I have four pairs of these rings. They are very well machined and very well finished. I used the alignment and lapping tools on my installations, but I could have easily skipped this step without any issues as no excess material was removed. Alignment has been perfect and grip on the scope tubes is excellent as well. I have switched scopes multiple times and have not had any issues with ring marks on the scope tubes, unlike other steel rings with poor alignment.

Awesome Rings! (27.10.2010)

I put the rings on an AR I hunt with and target shoot at 300-800 yds with. I was very impressed with the fit and finish on these rings. I lapped them in and it was the most even lapping job I have done, which is a testament to their machining. So far I have been very pleased.

Good Craftsmanship, but... (26.12.2011)

The quality and finish are excellent, with no tooling marks. I had a lot of difficulty adjusting the horizontal cant of my scope when following the included instructions. I tried to snug down one side and make adjustments from there, but only after I stopped using TSP's advice could I make it work. Very high quality product, instructions could be better.

Excellent rings (04.02.2013)

Very fine quality

easy rings to install (29.04.2014)

Used on a new AR-15 and getting the scope not to tilt, when tightening the screws, after getting it straight was as simple as 123.
Will be using them again and again and again!

Great Rings (28.06.2016)

Very nice rings. High quality at a good price. I lapped these rings, but after a strokes I could tell they didn't need to be lapped. I own two sets of the TPS rings. Think I need more.

Great picatinny aluminum rings! (23.05.2010)

Much better quality than a set of Burris XTR tactical rings I have. Good price, well made, look good. I used them to mount a scope with an EGW picatinny rail on a new Winchester M70 Coyote Light.

Great Rings! (21.01.2011)

Well made, good finish

Junk (13.02.2012)

My rings fell apart after 37 rounds. The claw on the bottom of the mount sheared off and TPS was completely unwilling to help.

Broke during installation. (06.03.2016)

While mounting the base to the rifle with a torque wrench set at 15 lbs, the base snapped.

Never had any problems (10.06.2017)

I've purchased several sizes in aluminum w/o any problems . Maybe the previous reviewer should read up on torque specs before bashing !!!! Tighten to 15 lbs ?????? Hello proper torque is in inch/pounds !!! I usually go by the scope manufacturers recommendations. Usually between 18-25 inch/pounds . Every set I purchased are top quality ,well machined and provide rock solid mounting .I won't hesitate to buy another set of TPS aluminum rings .

Excellent 1" scope rings (20.11.2017)

These high quality rings are a good value and perform well. Have used them on five rifles and they have worked perfectly so far. They come with clear instructions and are designed to be installed on Weaver or picatinny type rails and torqued to 65 in./lbs. - NOT ft./lbs...

The ring screws are designed to be torqued to 15 in./lbs. Read and follow the instructions and they will serve you well.

Lesen Sie 25 weitere Bewertungen bei brownells.com

204.9 204.9 1 CHF

Artikel-Nr.: 100020389
TPS PRODUCTS 35MM MEDIUM (1.185") STEEL RINGS
Herstellerproduktnummer: 30701 071611307017 Die TSR-Serie Ringe sind präzise aus einem Aluminiumblock gefräst, mit Toleranzen von .0002", was maximalen Kontakt zwischen Zielfernrohr und Ring gewährleistet. Hält das Zielfernrohr sicher gegen Rückstoss. Der Vier-Schrauben-Kappen ermöglicht es dir, das Absehen auszurichten, die linke Seite der Kappe festzuziehen und dann die rechte Seite, ohne dass sich das Zielfernrohr dreht. Abgerundete Kanten und Ecken helfen, Hängenbleiben zu vermeiden und sorgen für ein attraktives Aussehen. Die grosse Klemmmutter ermöglicht es dir, die Ringe an Mil-STD 1913 (Picatinny) Basen anzuziehen.

204.9 CHF 0 CHF 204.90 *

Nachbestellt, Lieferzeit ca. 4-12 Wochen aus dem Lager USA.

Eigenschaften: Art: Steel Grösse: Medium Höhe: 1.185'' Material: Steel Rohrdurchmesser des Zielfernrohres: 35mm

Auf die Wunschliste setzen

Frage stellen

Details

Auf die Wunschliste setzen

Frage stellen

Top Takeaways

Die TSR-Serie Ringe sind aus einem Aluminiumblock gefräst, was maximalen Kontakt zwischen Zielfernrohr und Ring gewährleistet.
Der Vier-Schrauben-Kappen ermöglicht es dir, das Absehen auszurichten, ohne dass sich das Zielfernrohr dreht.
Die grosse Klemmmutter ermöglicht es dir, die Ringe an Mil-STD 1913 (Picatinny) Basen anzuziehen.

Eigenschaften

Art: Steel Grösse: Medium Höhe: 1.185'' Material: Steel Rohrdurchmesser des Zielfernrohres: 35mm Versandgewicht: 0.045kg Versandhöhe: 58mm Versandbreite: 58mm Versandlänge: 94mm UPC : 071611307017

Artikeldetails

Made in USA

Entdecke die TSR Picatinny Scope Ringe von TPS! 🎯 Präzise, robust und ideal für dein Zielfernrohr. Maximaler Halt und einfache Montage.

Super Holding Power, Precision Alignment

SPECS: 7075-T651 Aluminum Alloy, matte black, hard anodized to Mil-A-8625 standards. 5/8" (15.8mm) wide. Height measured from top of base to center of ring. 30mm - High: 1.225" (31.1mm).

Mehr...

Super Haltekraft, Präzise Ausrichtung

Mehr...

Kundenbewertungen zu TPS PRODUCTS 35MM MEDIUM (1.185") STEEL RINGS

Anzahl der Bewertungen: 25
Von brownells.com: 25
Durchschnittliche Bewertung: 4.6

Great Rings (16.04.2010)

Great value, but not tall enough for AR (11.05.2011)

Height seems fine (20.03.2012)

Solid performer (18.09.2012)

Great rings (28.11.2011)

For the money these are the best rings you can get. I have them on three of my bolt guns and one of my AR-15's. TPS mounts are great too.

Best value rings I have used (06.03.2012)

These were recommended by a friend and he was correct. Excellent value for money.

Better than the rest (08.01.2010)

These are top of the line rings, they are better due to their quality control. There is no need to lap them like with badger. and the price is half of what you'd pay for .

Outstanding Quality (16.03.2015)

I highly recommend these rings.

The quality is equal to another set that I paid twice as much for. They are very solid, have an excellent finish, and mounted perfectly. I am very happy with them.

Excellent Rings (23.11.2009)

This is my second set of TPS/TSR rings. They come with detailed instructions. The finish and quality are very good. The high rings worked great for me mounted on an AR-15.

Great product (12.12.2009)

High quality, rugged, and good looking.

Best rings for the money (08.01.2010)

Exceptional (17.12.2010)

These rings allowed me to mount a 50mm scope on a PRI "tube". The threaded portion of the shaft allows for positive mounting. The instructions are very detailed and should be followed.

A Great Value In A Tactical Ring (21.06.2009)

Excellent Robust Rings (30.08.2010)

Awesome Rings! (27.10.2010)

Good Craftsmanship, but... (26.12.2011)

Excellent rings (04.02.2013)

Very fine quality

easy rings to install (29.04.2014)

Used on a new AR-15 and getting the scope not to tilt, when tightening the screws, after getting it straight was as simple as 123.
Will be using them again and again and again!

Great Rings (28.06.2016)

Very nice rings. High quality at a good price. I lapped these rings, but after a strokes I could tell they didn't need to be lapped. I own two sets of the TPS rings. Think I need more.

Great picatinny aluminum rings! (23.05.2010)

Much better quality than a set of Burris XTR tactical rings I have. Good price, well made, look good. I used them to mount a scope with an EGW picatinny rail on a new Winchester M70 Coyote Light.

Great Rings! (21.01.2011)

Well made, good finish

Junk (13.02.2012)

My rings fell apart after 37 rounds. The claw on the bottom of the mount sheared off and TPS was completely unwilling to help.

Broke during installation. (06.03.2016)

While mounting the base to the rifle with a torque wrench set at 15 lbs, the base snapped.

Never had any problems (10.06.2017)