Lightweight, extended bolt release has a finger lever that extends an additional 1⁄8". Lets you lock the bolt open using just one finger, and without fumbling. A slight pull on the bolt handle and the bolt releases. Gives fast, convenient reloads. Available in Titanium, steel or stainless steel for the 10/22®; requires no modifications to rifle.
SPECS: Titanium, natural silver finish.
Mehr...
Einfache, fumblefreie Bolt Release
Die leichte, verlängerte Bolt Release verfügt über einen Fingerhebel, der zusätzlich 1⁄8" herausragt. Damit kannst du den Bolt mit nur einem Finger und ohne Fummeln offen halten. Ein leichter Zug am Boltgriff und der Bolt wird freigegeben. Ermöglicht schnelles und bequemes Nachladen. Erhältlich in Titan, Stahl oder rostfreiem Stahl für die 10/22®; erfordert keine Modifikationen am Gewehr.
SPECS: Titan, natürliche Silberoberfläche.
Mehr...
Kundenbewertungen zu POWER CUSTOM 10/22® EXTENDED BOLT RELEASE, TITANIUM
Anzahl der Bewertungen: 4
Von brownells.com: 4
Durchschnittliche Bewertung: 3
Works fine, finish is lacking.(05.04.2011)
I replaced 3 of my stock Ruger bolt releases with 3 of these auto bolt releases from Power Custom. They works fine other than they are a little hard to operate due to a rough texture/finish. After a couple of range sessions they didn't smooth up, so I pulled all 3 out and buffed them with a bit of rouge. They work fine now. Wish I had gone with some of the less expensive products with better reviews. Also, I don't see any thing "extended" about them.
If they arrive okay, they are great...(11.11.2011)
Had I written this after replacing the first one, it would have recieved a "5". Everything dropped in place within minutes and worked as advertised. Then I changed the second one...
First, the tab angle was not the same as the first and had to be "tweeked". Second, this one had a much rougher finish which did not allow it to fit properly properly. Third, the holes were not the same dimension as the first (which I pulled back out to compare).
A guy at the range changed his out with the exact same part - only issue he had was the texture which he was able to smooth out and now works fine.
I would recommend this with caution only because the QA didn't catch the bad part.
Best check out I have ever seen BZ to Ya(19.09.2014)
THE extended bolt release will save my finger screwdriver and pliers to release the bolt , this will make faster shooting on the range. Now the RSO will not laugh at my trying to close the bolt
Now the hard part will bo installing this part without blood shed and cussing any and everything that walks the planet LOL maybe a gunsmith is needed
perhaps!!!! HAND DON
Didn't work without modifications(05.06.2017)
It did not work right off the bat when I put it in. With some filing of the surface to smooth it out and more filing of the bolt catch area, I got it to work. Ultimately I could have done the same thing with my original part and not bought this. I should have sent it back when it didn't work out of the box.
Artikel-Nr.: 713000005 POWER CUSTOM 10/22® EXTENDED BOLT RELEASE, TITANIUM Herstellerproduktnummer: NONE Die leichte, verlängerte Bolt Release verfügt über einen Fingerhebel, der zusätzlich 1⁄8" herausragt. Damit kannst du den Bolt mit nur einem Finger und ohne Fummeln offen halten. Ein leichter Zug am Boltgriff und der Bolt wird freigegeben. Ermöglicht schnelles und bequemes Nachladen. Erhältlich in Titan, Stahl oder rostfreiem Stahl für die 10/22®; erfordert keine Modifikationen am Gewehr.
41.9CHF0CHF 41.90
*
Nachbestellt, Lieferzeit ca. 4-12 Wochen aus dem Lager USA.
Made in USA
US-Exportklassifizierung: 0A501.x
Dieses Produkt unterliegt der Aufsicht der Regierung der Vereinigten Staaten von Amerika und ist ausschliesslich für den Export in das Bestimmungsland zur Verwendung durch den endgültigen Empfänger oder Endverbraucher, der beim Kauf festgelegt wird, bestimmt. Dieses Produkt darf ohne vorherige Erlaubnis der Regierung der Vereinigten Staaten von Amerika oder einer autorisierten US-Behörde über den endgültigen Empfänger oder Endverbrauchers hinaus nicht wiederverkauft, übertragen, oder in einer anderen Weise in Drittländer oder an Dritte überlassen werden. Dies gilt auch dann, wenn die Artikel verbaut bzw. in einen anderen Artikel integriert wurde.
This item is controlled by the U.S. government and authorized for export only to the country of ultimate destination for use by the ultimate consignee or end-user(s) herein identified. It may not be resold, transferred, or otherwise disposed of, to any other country or to any person other than the authorized ultimate consignee or end-user(s), either in their original form or after being incorporated into other items, without first obtaining approval from the U.S. government or as otherwise authorized by U.S. law and regulations.
Artikel-Nr.: 713000076 POWER CUSTOM 10/22® EXTENDED BOLT RELEASE, STEEL Herstellerproduktnummer: 10-22ABRBBLACK Die leichte, verlängerte Bolt Release verfügt über einen Fingerhebel, der zusätzlich 1⁄8" herausragt. Damit kannst du den Bolt mit nur einem Finger und ohne Fummeln offen halten. Ein leichter Zug am Boltgriff und der Bolt wird freigegeben. Ermöglicht schnelles und bequemes Nachladen. Erhältlich in Titan, Stahl oder rostfreiem Stahl für die 10/22®; erfordert keine Modifikationen am Gewehr.
39.9CHF0CHF 39.90
*
Nachbestellt, Lieferzeit ca. 4-12 Wochen aus dem Lager USA.
Lightweight, extended bolt release has a finger lever that extends an additional 1⁄8". Lets you lock the bolt open using just one finger, and without fumbling. A slight pull on the bolt handle and the bolt releases. Gives fast, convenient reloads. Available in Titanium, steel or stainless steel for the 10/22®; requires no modifications to rifle.
SPECS: Titanium, natural silver finish.
Mehr...
Einfache, fumblefreie Bolt Release
Die leichte, verlängerte Bolt Release verfügt über einen Fingerhebel, der zusätzlich 1⁄8" herausragt. Damit kannst du den Bolt mit nur einem Finger und ohne Fummeln offen halten. Ein leichter Zug am Boltgriff und der Bolt wird freigegeben. Ermöglicht schnelles und bequemes Nachladen. Erhältlich in Titan, Stahl oder rostfreiem Stahl für die 10/22®; erfordert keine Modifikationen am Gewehr.
SPECS: Titan, natürliche Silberoberfläche.
Mehr...
Kundenbewertungen zu POWER CUSTOM 10/22® EXTENDED BOLT RELEASE, TITANIUM
Anzahl der Bewertungen: 4
Von brownells.com: 4
Durchschnittliche Bewertung: 3
Works fine, finish is lacking.(05.04.2011)
I replaced 3 of my stock Ruger bolt releases with 3 of these auto bolt releases from Power Custom. They works fine other than they are a little hard to operate due to a rough texture/finish. After a couple of range sessions they didn't smooth up, so I pulled all 3 out and buffed them with a bit of rouge. They work fine now. Wish I had gone with some of the less expensive products with better reviews. Also, I don't see any thing "extended" about them.
If they arrive okay, they are great...(11.11.2011)
Had I written this after replacing the first one, it would have recieved a "5". Everything dropped in place within minutes and worked as advertised. Then I changed the second one...
First, the tab angle was not the same as the first and had to be "tweeked". Second, this one had a much rougher finish which did not allow it to fit properly properly. Third, the holes were not the same dimension as the first (which I pulled back out to compare).
A guy at the range changed his out with the exact same part - only issue he had was the texture which he was able to smooth out and now works fine.
I would recommend this with caution only because the QA didn't catch the bad part.
Best check out I have ever seen BZ to Ya(19.09.2014)
THE extended bolt release will save my finger screwdriver and pliers to release the bolt , this will make faster shooting on the range. Now the RSO will not laugh at my trying to close the bolt
Now the hard part will bo installing this part without blood shed and cussing any and everything that walks the planet LOL maybe a gunsmith is needed
perhaps!!!! HAND DON
Didn't work without modifications(05.06.2017)
It did not work right off the bat when I put it in. With some filing of the surface to smooth it out and more filing of the bolt catch area, I got it to work. Ultimately I could have done the same thing with my original part and not bought this. I should have sent it back when it didn't work out of the box.