Votre panier est vide.

Panier

Aide et contact

Livraison standard gratuite pour les commandes de plus de 399 CHF

Politique de retour de 100 jours

Newsletter

Promotions

Plus de 300 000 clients - nous vous disons merci !

4,93/5 "Très bien" (1400+ avis)

40 000+ produits pour la chasse et le tir sportif

BROWNELLS
.146x48 OVERSIZE 6-48 SCREW SHOP KIT

050806018501 080719112

Saves Your "Tail Feathers" If A Hole Gets Stripped

Slightly larger in diameter than the common 6-48 scope base mounting screw. Most holes "ruined" while drilling or tapping can be fixed; just retap to .146"-48 and install. No need to redrill base or gun. Thanks to Doug Knowt for his tip. Click Here for taps.

SPECS: .146"-48x½" (12.7mm) slotted machine screws, blued finish. Fillister and Weaver-style head. Kit contains 48 of each style, 1 taper tap, 1 bottom tap, and 1 Screw Gizzie in a bench box.

Plus...

Évite de "perdre la face" si un trou est endommagé

Légèrement plus large que la vis de montage de base de lunette 6-48 courante. La plupart des trous "endommagés" lors du perçage ou du taraudage peuvent être réparés ; il suffit de retarauder à .146"-48 et d'installer. Pas besoin de percer à nouveau la base ou l'arme. Merci à Doug Knowt pour son conseil. Cliquez ici pour les tarauds.

SPÉCIFICATIONS : vis à machine fendue de .146"-48x½" (12,7 mm), finition bleue. Tête de type Fillister et Weaver. Le kit contient 48 de chaque style, 1 taraud conique, 1 taraud de fond et 1 Screw Gizzie dans une boîte de rangement.

Plus...

Évaluations client de BROWNELLS OVERSIZE FILLISTER .146 -48 SCREWS 12 PACK

Nombre d'évaluations: 7
De brownells.com: 7
Note moyenne: 4.9

Saves a job gone bad! (05.09.2010)

8-40 Torx screws into a Remington 1100 stripped out the receiver. These screws, combined with the .146"-48 tap worked perfectly! As noted in tips description by Mr. Doug Knowt, no need to re-drill. Just run the tap through, install the oversize screws, and your done! The screw heads were exact size as Torx, and the screws were plenty long enough to grind to fit any application. Thanks Brownell's! Thanks Mr. Knowt!

Just the ticket! (01.07.2016)

I used these in conjunction with the required tap to fix the scope base screw holes in a Remington 597 receiver. The screw holes were a bit oversized as it came from the factory with only .002" of thread engagement.

Excellent fix! - almost perfect (14.06.2018)

I used these in conjunction with the associated tapered tap to fix the scope base screw holes in a Remington 700 receiver. The front two screws from the factory were stripped and would just spin. I had to drive them down through the holes after removing the barrel. The tapered tap did its' job by hand. Used the tap and a 1/8" drill bit on a piece of O-1 steel to allow me to cut and file the screws down to size. The only issue with these screws is the slotted head. My Burris XTR steel scope base calls for 35 in lbs of torque and the little slotted screw head wouldn't hold the bit all of the way to 35 in lbs of torque. A socket head or torx head would do the trick and would have made this solution perfect. Very happy overall though, I recommend this solution for stripped receiver scope base holes.

Receiver saver! (14.04.2011)

This kit was great and easy to use. A friend and I purchased after both had stripped out screws on Ruger 10/22 receivers. Bought this kit and the proper drill bit. Shortly after had new threaded holes in the receiver and scope rails mounted, with much less torque this time. Used Brownells video on how to make a screw jig from flat stock instead of using the gizzie. Have fixed 3 other receivers for a buddy at the local gun shop and more than paid for the kit.

Great kit for 10/22 (14.07.2014)

This kit made fixing stripped holes in a 10/22 receiver

a snap! Thanks Brownell's.

Simple to use. (12.03.2016)

I used the kit to repair a Ruger 10-22 with a stripped scope mount/receiver screw. I only fixed the damaged screw hole. (Hey, if it isn't broke, don't fix it) The Kit comes with 2 taps, one gizzy and a bunch of screws. Useless instructions. The tap with a point is the taper tap, and you use it for holes that go all-the-way through, and you use it to start all holes because you need the pointed end to initiate the holes. The bottom tap is the one with the blunt end. You would use it for holes that do not go completely through. Again, start with the pointed tap. The kit does not come with a handle, so I bought a cheap 3-piece kit from Harbor Freight for $7.00. I clamped my receiver in a padded vise, made it as level as I could, sprayed a bit of WD-40 on the tap and in the receiver screw hole, and turned it in by hand with the taper tap. Easy as pie. The Gizzy wasn't threaded, so I ran the taper tap through the small hole on the gizzy, and then threaded one of the screws in until it was about the same length as my factory scope mount screws. I didn't measure it (I should have). About a minute on my grinder, and I checked the fit of the screw using the scope mount and 10-22 receiver. Make sure the screws don't extend too far into the receiver, because the bolt with make contact with it. Overall, it's a pretty simple kit, and I don't have to ship the gun back to Ruger or take it to a gun smith. They include enough screws to repair a few dozen rifles. According to Ruger, don't use Loc tite on the 10-22. Evidently, it adds a bit of pressure, and is the cause of countless stripped receivers. Good luck.

Excellent!! (06.04.2017)

Purchased a 541S at the local gun shop,not realizing three of the four base holes were stripped until trying to mount a base..This kits bottoming tap and the included oversize screws(after shortening to length) saved the day..Worked perfect,worth every penny. Thanks Brownells!

Lire 7 plus d'avis sur brownells.com

21.9 134.9 3 CHF

Référence: 080719112
BROWNELLS OVERSIZE FILLISTER .146 -48 SCREWS 12 PACK
Ref Fabricant: 89165 050806018501 Légèrement plus large que la vis de montage de base de lunette 6-48 courante. La plupart des trous "endommagés" lors du perçage ou du taraudage peuvent être réparés ; il suffit de retarauder à .146"-48 et d'installer. Pas besoin de percer à nouveau la base ou l'arme. Merci à Doug Knowt pour son conseil. Cliquez ici pour les tarauds.

23.9 CHF 0 CHF 23.90 *

En rupture de stock, délai de livraison d'environ 4-12 semaines depuis l'entrepôt des États-Unis.

Ajouter à la Liste d'Envies

Poser un question

Propriétés

Ajouter à la Liste d'Envies

Poser un question

Points forts

Ces vis sont légèrement plus larges que les vis de montage de lunette 6-48 standard.
Réparez facilement les trous abîmés en retaraudant à .146"-48 sans avoir à percer à nouveau.
Le kit comprend 48 vis de chaque style, ainsi que des tarauds et un Screw Gizzie.

Caractéristiques

Poids du colis: 0.009kg Largeur d'expédition: 83mm Longueur d'expédition: 146mm UPC : 050806018501

Détails de l'article

Fabriqué au USA

Référence: 080719212
BROWNELLS OVERSIZE WEAVER .146" -48 SCREWS 12 PACK
Ref Fabricant: W05-719-212 050806018518 Légèrement plus large que la vis de montage de base de lunette 6-48 courante. La plupart des trous "endommagés" lors du perçage ou du taraudage peuvent être réparés ; il suffit de retarauder à .146"-48 et d'installer. Pas besoin de percer à nouveau la base ou l'arme. Merci à Doug Knowt pour son conseil. Cliquez ici pour les tarauds.

21.9 CHF 139 CHF 21.90 *

Délai de livraison environ 8-15 jours depuis l'entrepôt des États-Unis.

Ajouter à la Liste d'Envies

Poser un question

Propriétés

Ajouter à la Liste d'Envies

Poser un question

Référence: 080719000
BROWNELLS OVERSIZE .146 -48 SCREW SHOP KIT 050806018495 Légèrement plus large que la vis de montage de base de lunette 6-48 courante. La plupart des trous "endommagés" lors du perçage ou du taraudage peuvent être réparés ; il suffit de retarauder à .146"-48 et d'installer. Pas besoin de percer à nouveau la base ou l'arme. Merci à Doug Knowt pour son conseil. Cliquez ici pour les tarauds.

134.9 CHF 0 CHF 134.90 *

En rupture de stock, délai de livraison d'environ 4-12 semaines depuis l'entrepôt des États-Unis.

Ajouter à la Liste d'Envies

Poser un question

Propriétés

Ajouter à la Liste d'Envies

Poser un question

Réparez facilement vos trous endommagés avec le kit de vis .146x48 de BROWNELLS. 🛠️ Contient 12 vis Fillister et tarauds pour un montage parfait!

Saves Your "Tail Feathers" If A Hole Gets Stripped

SPECS: .146"-48x½" (12.7mm) slotted machine screws, blued finish. Fillister and Weaver-style head. Kit contains 48 of each style, 1 taper tap, 1 bottom tap, and 1 Screw Gizzie in a bench box.

Plus...

Évite de "perdre la face" si un trou est endommagé

Plus...