Il Carrello è vuoto.

Carrello

Aiuto e contatti

Spedizione gratuita con ordini superiori ad CHF 399

Politica di restituzione di 100 giorni

Newsletter

Offerte

Oltre 300.000 clienti - vi ringraziamo!

4,93/5 "Molto buono" (1400+ recensioni)

Oltre 40.000 prodotti per caccia e sport di tiro

CASPIAN
1911 SLIDES

168000101

Superb Strength & Precise Tolerances For The Ultimate Combat Pistol

Custom-quality slides from Caspian, ready to be fitted to the frame of your choice. They start as high-quality forgings for extra strength, then are heat-treated to Rc 38-41 before machining for exceptional dimensional stability. Sides are polished, while the rest of the surface is bead-blasted for a non-glare, matte finish. Deep-cut, forward-angled rear cocking serrations prevent slippage when racking, even with a wet hand. Available in 4340 carbon steel (CS) and 416 stainless steel (SS) with .45 ACP, .40 S&W, and 9mm breechfaces. Commander and Officers models in .45 ACP only. Choose a slide without sight cuts (NC), or between two pre-cut dovetail options: a Novak Lo-Mount or Bo-Mar BMCS rear cut, both coupled with a Novak front cut. Recon slide is a Government slide with ball cuts at the front that line up with the light rail on the Caspian Recon frame (available separately). All slides require the use of a 9mm/.38 Super firing pin.

SPECS: 4340 carbon steel, in-the-white, or 416 stainless steel, natural finish. Government model accepts 5" barrel. Commander accepts 4.25" barrel. Officers model accepts 3.5" barrel. All Caspian slides require the use of a 9mm/.38 Super firing pin.

Altro...

Superba Resistenza & Tolleranze Precise Per Il Pistol Combat Definitivo

Carrelli di qualità personalizzata da Caspian, pronti per essere adattati al telaio di tua scelta. Iniziano come forgings di alta qualità per una maggiore resistenza, quindi vengono trattati termicamente a Rc 38-41 prima della lavorazione per un'eccezionale stabilità dimensionale. I lati sono lucidati, mentre il resto della superficie è sabbiato per una finitura opaca e senza riflessi. Le scanalature di presa posteriori angolate in avanti e profonde prevengono lo scivolamento durante il caricamento, anche con una mano bagnata. Disponibili in acciaio al carbonio 4340 (CS) e acciaio inossidabile 416 (SS) con facce di chiusura da .45 ACP, .40 S&W e 9mm. Modelli Commander e Officers disponibili solo in .45 ACP. Scegli un carrello senza tagli per mirini (NC), oppure tra due opzioni di dovetail pre-tagliate: un taglio posteriore Novak Lo-Mount o Bo-Mar BMCS, entrambi abbinati a un taglio anteriore Novak. Il carrello Recon è un carrello Government con tagli a sfera nella parte anteriore che si allineano con il binario leggero sul telaio Caspian Recon (disponibile separatamente). Tutti i carrelli richiedono l'uso di un percussore da 9mm/.38 Super.

SPECIFICHE: acciaio al carbonio 4340, in bianco, o acciaio inossidabile 416, finitura naturale. Il modello Government accetta canne da 5". Il modello Commander accetta canne da 4.25". Il modello Officers accetta canne da 3.5". Tutti i carrelli Caspian richiedono l'uso di un percussore da 9mm/.38 Super.

Altro...

Punteggi dei clienti per CASPIAN COMMANDER, CS, LOW MOUNT SIGHT CUT, 45 ACP

Numero di punteggi: 6
Da brownells.com: 6
Punteggio medio: 3.8

Very nice slide! (12.08.2012)

Fit perfectly except for a little work to get the barrel bushing to fit. I'm extremely happy with it. It isn't quite a "drop in replacement" but, I had no trouble fitting it to my frame. I highly recommend it as a replacement slide for a Colt Officers model. Especially, since the actual Colt ones are getting harder to find.

Not for all (20.04.2012)

I ordered the slide for my build, a 45 ACP, the slide looks great and is good quality. I was hopeing to be able to switch slides back and forth, between the Gov and commander modle. The slide did not fit at all on the frame, so I took it to my local gunsmith to have it fitted, after about a week he notified me that not only uses a 9 mm fireing pin (which I knew) but also a 9 mm ejector (not mentioned anywhere) and that the 45 ACP ejector would not work at all. So as soon as my gunsmith puts the 45 back into its original configuration, I'll try to figure something else out. My recomendation, if you have a Mil Spec 45 this slide may not be for you.

Exactly what i wanted, Quick, Easy (19.03.2010)

This slide is a stainless commander length, of course. It has the rear slanted classic style serrations. NO front serrations, lowered and flared ejection port, Caspian "C" logo on both sides under the rear sight and CASPIAN engraved in the left ( I think, i don't have it in front of me.) It is well finished, NO burrs, If there are any machine marks, they are not visible or i missed them. Edges were crisp but not sharp. I will end up rounding off all edges though. When i got it, it was in a box from Caspian with the stainless note (says if you aren't careful/fit the slide improperly there is a possibility you can break off the rear left part, the notch behind where the thumb safety locks in. IF YOU BREAK IT, YOUR SLIDE WILL NOT BE REPLACED) and some type of grease paper. [...]The slide would go about half way down my frame, which i think is about perfect. I haven't got to fit it yet but I am confident it will fit right. I have a used factory Colt .45 barrel going in it for now and it locked and unlocked very nicely. Locked SOLID. The factory barrel bushing that went with the Colt barrel fit very tight in the slide, but went in correctly. Very good. the firing pin and spring went in no issue ( small diameter firing pin [.38]) The extractor goes all the way in but fits very tight, i think i will sand a couple thousands off of it just to get it in and out. The one thing i didn't try was to see if the firing pin stop went in without fitting, and I haven't received my sights yet, so i can't say how they fit. I am very pleased. I was not able to find another slide i liked anywhere except Caspian themselves, the issue there is the wait while they build it, not that that is bad. I am very "picky when it comes to guns, cars, women, and parts for all..... I know what i want to build before i start. This slide actually exceeded my expectations. I will order another Caspian the next time i build a 1911.P.S. In this review, further down, it has multiple choices for pros and cons. One listed under cons is fitting required. I think this is good. I want every part to fit my gun as well as possible. Some may want to buy a part and it go straight on, thats fine too. SO, my opinion is that minor fitting is a pro. As

Not so good. (04.10.2014)

Not much about this slide was good, but may have just been my luck at getting a not so good one. The front Novak sight cut was bad and took me 4 hours with a file and a knife edge stone to get it to work. I have tried 4 different barrels and hours of filing and stoning and I still can't get one to lock up right. Might be just my luck, but I may not buy another one, ever.....

New Project (29.10.2011)

I mated this slide to a stainless Essex frame I previously had fit a Remington Rand blued slide on. The Caspian slide completed the all stainless look, and I fit an Ed Brown stainless barrel Colt Commander bobbed hammer and Smith and Alexander Mainspring. The frames blued componets were removed and replaced with all stainless slide lock, safety and mag release. The final product is a great looking, great shooting chunk of shiny 1911!

**Springfield rebuild** (11.12.2016)

Fitted this SS Caspian slide to a Springfield Armory 1911-A1 frame. Rebuilt this 1911 with all new parts from Brownell's. The fit and finish of this slide is beautiful. I would definitely choose Caspian for all my future builds.

<img width="500" src='/userdocs/reviewimages/6c1c11d3-788f-4011-b5c4-bfdf0d081392.jpg' alt=''>

Leggi più recensioni su brownells.com

375.89 659.9 16 CHF

N. prodotto: 168000101
CASPIAN COMMANDER, CS, LOW MOUNT SIGHT CUT, 45 ACP
Parti Fabbricante: 168-000-101 Carrelli di qualità personalizzata da Caspian, pronti per essere adattati al telaio di tua scelta. Iniziano come forgings di alta qualità per una maggiore resistenza, quindi vengono trattati termicamente a Rc 38-41 prima della lavorazione per un'eccezionale stabilità dimensionale. I lati sono lucidati, mentre il resto della superficie è sabbiato per una finitura opaca e senza riflessi. Le scanalature di presa posteriori angolate in avanti e profonde prevengono lo scivolamento durante il caricamento, anche con una mano bagnata. Disponibili in acciaio al carbonio 4340 (CS) e acciaio inossidabile 416 (SS) con facce di chiusura da .45 ACP, .40 S&W e 9mm. Modelli Commander e Officers disponibili solo in .45 ACP. Scegli un carrello senza tagli per mirini (NC), oppure tra due opzioni di dovetail pre-tagliate: un taglio posteriore Novak Lo-Mount o Bo-Mar BMCS, entrambi abbinati a un taglio anteriore Novak. Il carrello Recon è un carrello Government con tagli a sfera nella parte anteriore che si allineano con il binario leggero sul telaio Caspian Recon (disponibile separatamente). Tutti i carrelli richiedono l'uso di un percussore da 9mm/.38 Super.

579.9 CHF 2 CHF 579.90 *

Tempi di consegna circa 8-15 giorni dal magazzino negli Stati Uniti.

Caratteristiche: Adatto per: 1911 Cartuccia: 45 Aua (ACP) Finitura: Semilavorata Mire: Novak Modello: Commander Tipo: Ricambio originale, Commander, Chiusura posteriore

CASPIAN 1911 SLIDES

Punteggi dei clienti per CASPIAN COMMANDER, CS, LOW MOUNT SIGHT CUT, 45 ACP

Restrizioni

Top takeaways

Caratteristiche

Dettagli dell'elemento

Punteggi dei clienti per CASPIAN COMMANDER, CS, LOW MOUNT SIGHT CUT, 45 ACP

Collegare

Metodi di pagamento sicuri

Associazioni di categoria

Benvenuti!

CASPIAN
1911 SLIDES