Low-friction Delrin disk fits on the end of the buffer spring, opposite the buffer, and stops the annoying "twang" of the buffer hitting the rear of the receiver extension during recoil. Quick, easy installation, with no permanent alterations to gun. Simply remove buffer and spring, insert Twang Buster, then reinstall buffer and spring.
Ferma il Fastidioso Rumore del Buffer Durante il Rinculo
Il disco in Delrin a bassa frizione si adatta all'estremità della molla di buffer, opposto al buffer, e ferma il fastidioso "twang" del buffer che colpisce il retro dell'estensione del ricevitore durante il rinculo. Installazione rapida e semplice, senza modifiche permanenti all'arma. Basta rimuovere il buffer e la molla, inserire il Twang Buster, quindi reinstallare il buffer e la molla.
SPECIFICHE: Realizzato in Delrin termoplastico, nero. Si adatta ai tubi di estensione del ricevitore della molla di buffer A2 e M4-style carbine.
Altro...
Punteggi dei clienti per DOUBLE STAR TWANG BUSTER
Numero di punteggi: 12
Da brownells.com: 12
Punteggio medio: 2.9
Not bad(12.08.2010)
Does what it says although it causes bolt catch to malfuntion
works good(27.11.2010)
ive had it for 3 months works and have never had any problems with my rifle. would def recamend it.
Can be problematic.(17.08.2011)
It does reduce the twang as it says, but in my RRA it reduced the bolt stroke enough that my bold catch would not catch every time. It also caused my bolt to short stroke on occasion and jam the rifle. If you buy this, before installing lock back your bolt and carrier all the way by hand, hold it there and visual check the distance between your bolt face and bolt catch. After installing the buster check that gap again to see if you still have enough to compensate for loads that may not be full power. My RRA went from about a little less than a 1/4" gap to about 10 thousands only. Just thoroughly check function before relying on it.
Meh..(06.09.2011)
Does stop the annoying twang but it prevented the bolt catch from operating properly on my DPMS AP4. All in all, if you need your bolt catch to work I'd avoid this device, if you don't care about the bolt catch give it a shot.
DO NOT BUY JUNK(05.10.2011)
MADE MY BOLT CATCH INOPERABLE
Ok part(20.12.2011)
It does what it's supposed to do in regards to quieting down the spring noise. But it does have the annoying habit of not letting the bolt lock all the way back after the last round is fired. Not sure if this is due to the combo of running the recoil pad too. When I installed this I was only using .223 55gr, when I stepped up to 5.56 62gr, the issue was not there as often. I'll use it some more, but we'll see what happens in the next 300+rds.
works well in my 9mm dpms style ar(22.05.2012)
I bought one for my 9mm ar, and it worked perfectly, so I bought several more, and havn't had a single problem. Some of those over-power springs have a few extra coils, so the spring is longer when fully compressed. That may be the problem that others are having. If 1/16 inch piece of plastic is going to prevent your bolt from going all the way back, get a better spring. Those flat wire springs work great! Brownells # 452-000-119WB or 840-000-048WB
It deserves a higher rating. It works.(23.09.2012)
This product does everthing it says and nothing it does not. I install these in every AR I own and it does take the "twang" that all AR's make when fired. Anything to help make the weapon quieter is a good thing. If the "twang doesn't bother you, don't buy it. If you want that sound eliminated completely then I highly recommend it because it does do what it says.
Waste of money.(23.05.2014)
Installed and it did nothing. I removed it, re-read the instructions and re-installed. Still nothing. Changed springs to flat wire JP springs. Still no busting of the twang was going on in my full length A2 stock.
Works(22.10.2014)
Works as it claims. If Your having bolt locking problems in all likelihood your spring is A: too long or B: too stiff or C: A&B.
Had a friend with locking issues & his spring was using wire that was 0.005" thicker than mine. We swapped springs & swapped which rifle had the problem.
Save yer money(18.12.2014)
It's really the spring in the tube of the stock that "twangs" and this does nothing for that - in fact after installing it, the bolt wouldn't lock up manually or after the last shot. Can't return these fast enough.
Does not work as advertised,(22.05.2017)
I purchased the twang buster and installed it my Palmetto State Armory A2 lower buffer assembley. This product does absolutely nothing to reduce the sound of the buffer working, causes the buffer to bottom out too soon- resulting in excess wear on the face of the buffer being smashed by the bolt carrier, and as a kicker, is incredibly difficult to remove once installed. Do not purchase this item. Waste of time, waste of money, causes excess wear on your firearm.
N. prodotto: 100005392 DOUBLE STAR TWANG BUSTER Parti Fabbricante: JT140841348104704 Il disco in Delrin a bassa frizione si adatta all'estremità della molla di buffer, opposto al buffer, e ferma il fastidioso "twang" del buffer che colpisce il retro dell'estensione del ricevitore durante il rinculo. Installazione rapida e semplice, senza modifiche permanenti all'arma. Basta rimuovere il buffer e la molla, inserire il Twang Buster, quindi reinstallare il buffer e la molla.
14.9CHF10CHF 14.90
*
Tempi di consegna circa 8-15 giorni dal magazzino negli Stati Uniti.
Il Twang Buster in Delrin riduce il fastidioso "twang" del buffer durante il rinculo.
Installazione semplice senza modifiche permanenti, basta rimuovere e reinstallare il buffer e la molla.
Compatibile con tubi di estensione del ricevitore della molla di buffer A2 e M4-style carbine.
Caratteristiche
Adatto per:
AR-15
Colore:
Black
Materiale:
Thermoplastic
Peso della spedizione: 0.005kgLarghezza di spedizione: 76mmLunghezza di spedizione: 89mm
UPC
: 841348104704
Dettagli dell'elemento
Made in Usa
Classificazione per l'export dagli US: 0A501.x
Questi articoli sono controllati dal governo degli Stati Uniti e ne è autorizzata l'esportazione solo nel paese di destinazione finale e l'uso solo da parte del destinatario finale o degli utenti finali qui identificati. Questi beni non possono essere rivenduti, trasferiti o altrimenti ceduti a nessun altro paese o a persone diverse dal destinatario finale o dall'utente finale autorizzati, nella loro forma originale o dopo essere stati incorporati in altri articoli, senza prima ottenere l'approvazione dal governo degli Stati Uniti o come altrimenti autorizzato dalla legge e dai regolamenti degli Stati Uniti.
This item is controlled by the U.S. government and authorized for export only to the country of ultimate destination for use by the ultimate consignee or end-user(s) herein identified. It may not be resold, transferred, or otherwise disposed of, to any other country or to any person other than the authorized ultimate consignee or end-user(s), either in their original form or after being incorporated into other items, without first obtaining approval from the U.S. government or as otherwise authorized by U.S. law and regulations.
Elimina il fastidioso "twang" con il Twang Buster per AR-15! 🔧 Installazione semplice e senza modifiche permanenti.
Low-friction Delrin disk fits on the end of the buffer spring, opposite the buffer, and stops the annoying "twang" of the buffer hitting the rear of the receiver extension during recoil. Quick, easy installation, with no permanent alterations to gun. Simply remove buffer and spring, insert Twang Buster, then reinstall buffer and spring.
Ferma il Fastidioso Rumore del Buffer Durante il Rinculo
Il disco in Delrin a bassa frizione si adatta all'estremità della molla di buffer, opposto al buffer, e ferma il fastidioso "twang" del buffer che colpisce il retro dell'estensione del ricevitore durante il rinculo. Installazione rapida e semplice, senza modifiche permanenti all'arma. Basta rimuovere il buffer e la molla, inserire il Twang Buster, quindi reinstallare il buffer e la molla.
SPECIFICHE: Realizzato in Delrin termoplastico, nero. Si adatta ai tubi di estensione del ricevitore della molla di buffer A2 e M4-style carbine.
Altro...
Punteggi dei clienti per DOUBLE STAR TWANG BUSTER
Numero di punteggi: 12
Da brownells.com: 12
Punteggio medio: 2.9
Not bad(12.08.2010)
Does what it says although it causes bolt catch to malfuntion
works good(27.11.2010)
ive had it for 3 months works and have never had any problems with my rifle. would def recamend it.
Can be problematic.(17.08.2011)
It does reduce the twang as it says, but in my RRA it reduced the bolt stroke enough that my bold catch would not catch every time. It also caused my bolt to short stroke on occasion and jam the rifle. If you buy this, before installing lock back your bolt and carrier all the way by hand, hold it there and visual check the distance between your bolt face and bolt catch. After installing the buster check that gap again to see if you still have enough to compensate for loads that may not be full power. My RRA went from about a little less than a 1/4" gap to about 10 thousands only. Just thoroughly check function before relying on it.
Meh..(06.09.2011)
Does stop the annoying twang but it prevented the bolt catch from operating properly on my DPMS AP4. All in all, if you need your bolt catch to work I'd avoid this device, if you don't care about the bolt catch give it a shot.
DO NOT BUY JUNK(05.10.2011)
MADE MY BOLT CATCH INOPERABLE
Ok part(20.12.2011)
It does what it's supposed to do in regards to quieting down the spring noise. But it does have the annoying habit of not letting the bolt lock all the way back after the last round is fired. Not sure if this is due to the combo of running the recoil pad too. When I installed this I was only using .223 55gr, when I stepped up to 5.56 62gr, the issue was not there as often. I'll use it some more, but we'll see what happens in the next 300+rds.
works well in my 9mm dpms style ar(22.05.2012)
I bought one for my 9mm ar, and it worked perfectly, so I bought several more, and havn't had a single problem. Some of those over-power springs have a few extra coils, so the spring is longer when fully compressed. That may be the problem that others are having. If 1/16 inch piece of plastic is going to prevent your bolt from going all the way back, get a better spring. Those flat wire springs work great! Brownells # 452-000-119WB or 840-000-048WB
It deserves a higher rating. It works.(23.09.2012)
This product does everthing it says and nothing it does not. I install these in every AR I own and it does take the "twang" that all AR's make when fired. Anything to help make the weapon quieter is a good thing. If the "twang doesn't bother you, don't buy it. If you want that sound eliminated completely then I highly recommend it because it does do what it says.
Waste of money.(23.05.2014)
Installed and it did nothing. I removed it, re-read the instructions and re-installed. Still nothing. Changed springs to flat wire JP springs. Still no busting of the twang was going on in my full length A2 stock.
Works(22.10.2014)
Works as it claims. If Your having bolt locking problems in all likelihood your spring is A: too long or B: too stiff or C: A&B.
Had a friend with locking issues & his spring was using wire that was 0.005" thicker than mine. We swapped springs & swapped which rifle had the problem.
Save yer money(18.12.2014)
It's really the spring in the tube of the stock that "twangs" and this does nothing for that - in fact after installing it, the bolt wouldn't lock up manually or after the last shot. Can't return these fast enough.
Does not work as advertised,(22.05.2017)
I purchased the twang buster and installed it my Palmetto State Armory A2 lower buffer assembley. This product does absolutely nothing to reduce the sound of the buffer working, causes the buffer to bottom out too soon- resulting in excess wear on the face of the buffer being smashed by the bolt carrier, and as a kicker, is incredibly difficult to remove once installed. Do not purchase this item. Waste of time, waste of money, causes excess wear on your firearm.
Aiuto e contatti
Newsletter
Visualizzazione classica
Visualizzazione mobile