Fully machined from A2 tool steel with the hammer notch individually, surface ground to ensure an exact angle of engagement. Reduces felt trigger pull by up to 50 percent. Drop-in installation; use in an unaltered, factory triggerguard. Fits both the .22LR and .22WMR.
SPECS: A2 tool steel, in the white. Hardened to Rc 58.
Plus...
Réduit le poids de la détente pour améliorer la précision
Entièrement usiné en acier à outils A2 avec l'encoche du marteau usinée individuellement, rectifiée pour garantir un angle d'engagement précis. Réduit la pression du déclencheur ressentie jusqu'à 50 %. Installation facile ; à utiliser dans un garde-déclencheur d'origine, non modifié. S'adapte aux calibres .22LR et .22WMR.
SPECS: Acier à outils A2, brut. Trempé à Rc 58.
Plus...
Évaluations client de VOLQUARTSEN TARGET HAMMER
Nombre d'évaluations: 8
De brownells.com: 8
Note moyenne: 5
Worth the Effort(22.07.2010)
Just finished installing the hammer. Initial trigger pull approx. 4 1/2 lbs. according to spring gauge. After installation: 2 lbs. Minimal creep. Took about 15-20 minutes. Remove trigger housing from receiver by removing the one retaining pin at rear of trigger housing(if bolt is closed, may have to pull back slightly to get housing to pop free). Place housing in padded vice at a slight angle to avoid crushing mag release button. Housing is composite so easy does it. Tap out hammer pin with punch but just enough to release hammer-don't drive out all the way. Don't remove punch but leave in pin hole to keep spring and plastic bushing in place(there are two plastic bushings inside of spring on both sides of hammer). Remove old hammer and slide in new one, align pin holes and reinstall hammer pin. You may find that you cannot get the hammer to go to the cocked position. If this is so, you have to push the trigger fully forward and the hammer should stay in the cocked position now. Install housing back into receiver and replace the one retaining pin. Install upper assembly back into stock and your done. With gun empty, check to make sure rifle fires after bolt is cycled. Mine functioned flawlessly. If you completed the job without ending up with a bunch of extra parts, you should be very pleased with the results.
Money well spent!!(03.06.2011)
If you buy one part for your 597, make it this! Very easy installation and a dramatic difference in trigger pull. I still just can't believe how smooth and nice it is. Just buy it!!
BUY IT(25.12.2011)
Easy to install. Reduces triger pull. Smoother trigger. Buy it. You will love it.
Great Prodct!!(17.01.2012)
Slid this puppy right into my HB 597 after getting really good on-line videos do demonstrate (at Rimfirecentral.com) or elsewhere. It does exactly as claimed, makes trigger light and crisp.
Need to have in your Remington 597(13.11.2013)
I'm very pleased about this product, really surpised about how it works overrided my spectatives, my Rem597 is in a new level of trigger and shooting control. Very fast shipping and a real proffesional package. My first but not my last buy with brownells. Thanks a lot.
Effective Solution(02.12.2013)
This was the perfect solution for the VERY heavy trigger on my daughter's 597. Easy to install; but be patient with the pin for the hammer.
Now the pull is crisp and light, with no creep. Trigger pull was reduced by more than 50%
This product was very cost effective compared to some of the other solutions out there.
High Quality Product!
great product(02.09.2014)
This hammer combined with a Brownell's extractor made an otherwise misfiring and jamming gun shoot flawlessly. I was able to shoot four different types of ammo totaling about 400 rounds without any FTE or FTF. This gun out of the box did not function properly. Now it shoots great and is extremely accurate. A must upgrade for any Remington 597 owner!
YouTube Video helps(13.05.2016)
My 597 has a great barrel, but a lousy trigger. Getting the most out of your gun comes right down to the trigger. Why do you think benchrest shooters use 4 - 6 Oz. triggers. So I ordered this item with my fingers crossed. Got it promptly and installed it in 45 minutes. Use Youtube video (9min ) and it is very straight forward. End result Trigger pull 3 1/4 - 3 1/2 Lbs.
Référence: 930000019 VOLQUARTSEN TARGET HAMMER Ref Fabricant: VCRTH810162011321 Entièrement usiné en acier à outils A2 avec l'encoche du marteau usinée individuellement, rectifiée pour garantir un angle d'engagement précis. Réduit la pression du déclencheur ressentie jusqu'à 50 %. Installation facile ; à utiliser dans un garde-déclencheur d'origine, non modifié. S'adapte aux calibres .22LR et .22WMR.
79.9CHF5CHF 79.90
*
Délai de livraison environ 8-15 jours depuis l'entrepôt des États-Unis.
Fabriqué au USA
US export classification: 0A501.c
Ces articles sont contrôlés par le gouvernement des États-Unis et autorisés uniquement à être exportés vers le pays de destination finale pour être utilisés par le destinataire final ou les utilisateurs finaux identifiés dans le présent document. Ils ne peuvent être ni revendus, ni cédés à tout autre pays ou toute personne autre que le destinataire final autorisé ou l'utilisateur final, soit dans leur forme originale, soit après avoir été incorporés dans d'autres produits, sans l'accord préalable du gouvernement des États-Unis ou d'une autre manière autorisée par la législation américaine, règlements.
This item is controlled by the U.S. government and authorized for export only to the country of ultimate destination for use by the ultimate consignee or end-user(s) herein identified. It may not be resold, transferred, or otherwise disposed of, to any other country or to any person other than the authorized ultimate consignee or end-user(s), either in their original form or after being incorporated into other items, without first obtaining approval from the U.S. government or as otherwise authorized by U.S. law and regulations.
Améliore ton REMINGTON 597 avec le Volquartsen Target Hammer 🔧. Réduit la pression du déclencheur et facile à installer pour un tir précis !
Fully machined from A2 tool steel with the hammer notch individually, surface ground to ensure an exact angle of engagement. Reduces felt trigger pull by up to 50 percent. Drop-in installation; use in an unaltered, factory triggerguard. Fits both the .22LR and .22WMR.
SPECS: A2 tool steel, in the white. Hardened to Rc 58.
Plus...
Réduit le poids de la détente pour améliorer la précision
Entièrement usiné en acier à outils A2 avec l'encoche du marteau usinée individuellement, rectifiée pour garantir un angle d'engagement précis. Réduit la pression du déclencheur ressentie jusqu'à 50 %. Installation facile ; à utiliser dans un garde-déclencheur d'origine, non modifié. S'adapte aux calibres .22LR et .22WMR.
SPECS: Acier à outils A2, brut. Trempé à Rc 58.
Plus...
Évaluations client de VOLQUARTSEN TARGET HAMMER
Nombre d'évaluations: 8
De brownells.com: 8
Note moyenne: 5
Worth the Effort(22.07.2010)
Just finished installing the hammer. Initial trigger pull approx. 4 1/2 lbs. according to spring gauge. After installation: 2 lbs. Minimal creep. Took about 15-20 minutes. Remove trigger housing from receiver by removing the one retaining pin at rear of trigger housing(if bolt is closed, may have to pull back slightly to get housing to pop free). Place housing in padded vice at a slight angle to avoid crushing mag release button. Housing is composite so easy does it. Tap out hammer pin with punch but just enough to release hammer-don't drive out all the way. Don't remove punch but leave in pin hole to keep spring and plastic bushing in place(there are two plastic bushings inside of spring on both sides of hammer). Remove old hammer and slide in new one, align pin holes and reinstall hammer pin. You may find that you cannot get the hammer to go to the cocked position. If this is so, you have to push the trigger fully forward and the hammer should stay in the cocked position now. Install housing back into receiver and replace the one retaining pin. Install upper assembly back into stock and your done. With gun empty, check to make sure rifle fires after bolt is cycled. Mine functioned flawlessly. If you completed the job without ending up with a bunch of extra parts, you should be very pleased with the results.
Money well spent!!(03.06.2011)
If you buy one part for your 597, make it this! Very easy installation and a dramatic difference in trigger pull. I still just can't believe how smooth and nice it is. Just buy it!!
BUY IT(25.12.2011)
Easy to install. Reduces triger pull. Smoother trigger. Buy it. You will love it.
Great Prodct!!(17.01.2012)
Slid this puppy right into my HB 597 after getting really good on-line videos do demonstrate (at Rimfirecentral.com) or elsewhere. It does exactly as claimed, makes trigger light and crisp.
Need to have in your Remington 597(13.11.2013)
I'm very pleased about this product, really surpised about how it works overrided my spectatives, my Rem597 is in a new level of trigger and shooting control. Very fast shipping and a real proffesional package. My first but not my last buy with brownells. Thanks a lot.
Effective Solution(02.12.2013)
This was the perfect solution for the VERY heavy trigger on my daughter's 597. Easy to install; but be patient with the pin for the hammer.
Now the pull is crisp and light, with no creep. Trigger pull was reduced by more than 50%
This product was very cost effective compared to some of the other solutions out there.
High Quality Product!
great product(02.09.2014)
This hammer combined with a Brownell's extractor made an otherwise misfiring and jamming gun shoot flawlessly. I was able to shoot four different types of ammo totaling about 400 rounds without any FTE or FTF. This gun out of the box did not function properly. Now it shoots great and is extremely accurate. A must upgrade for any Remington 597 owner!
YouTube Video helps(13.05.2016)
My 597 has a great barrel, but a lousy trigger. Getting the most out of your gun comes right down to the trigger. Why do you think benchrest shooters use 4 - 6 Oz. triggers. So I ordered this item with my fingers crossed. Got it promptly and installed it in 45 minutes. Use Youtube video (9min ) and it is very straight forward. End result Trigger pull 3 1/4 - 3 1/2 Lbs.
Aide et contact
Newsletter
Vue classique
Vue mobile