Trims The Rivet Tip To Make Broken Ejector Spring Removal Simple
Hollow-end mill fits in drill press, spot faces the front rivet to take off just the peened area. Often lets you re-peen the existing rivet and eliminate rebluing the receiver.
Ritaglia il Punta del Rivetto per Rendere Semplice la Rimozione della Molla Eiettore Rotta
Il fresatore a estremità cava si adatta al trapano a colonna, preparando la faccia del rivetto anteriore per rimuovere solo l'area peened. Spesso consente di ripristinare il rivetto esistente ed eliminare la necessità di ripristinare la finitura del ricevitore.
SPECIFICHE: Asta in acciaio, cutter in acciaio temprato. Lunghezza 2½" (6.3cm), diametro dell'asta .31" (7.8mm). Diametro del cutter .143" (3.6mm).
Altro...
Punteggi dei clienti per BROWNELLS REMINGTON 870 EJECTOR SPRING RIVET CUTTER
Numero di punteggi: 1
Da brownells.com: 1
Punteggio medio: 5
Great investment!(10.02.2016)
This little rivet cutter made me save over $200 in gunsmithing work on my old 870 Wingmaster, which had been sitting in the gun safe for years because of a ''too-expensive-to-replace'' broken ejector spring. The instructions provided with the tool are very clear and allowed me, as indicated, to re-use the rivet to lock the new spring into the ejector. The only thing I did differently than prescribed by the instructions was to drive the rivet cutter down on the tiny rivet head by hand instead of using a press drill. The rivet cutter being very sharp and the rivet metal being very soft, I was afraid to ruin the rivet using a press drill. It took me 10 minutes to cut the rivet head slowly and safely by hand (clockwise twist of the fingers with little pressure).
N. prodotto: 080000040 BROWNELLS REMINGTON 870 EJECTOR SPRING RIVET CUTTER050806103825 Il fresatore a estremità cava si adatta al trapano a colonna, preparando la faccia del rivetto anteriore per rimuovere solo l'area peened. Spesso consente di ripristinare il rivetto esistente ed eliminare la necessità di ripristinare la finitura del ricevitore.
54.9CHF0CHF 54.90
*
In arretrato, tempi di consegna circa 4-12 settimane dal magazzino negli Stati Uniti.
Trims The Rivet Tip To Make Broken Ejector Spring Removal Simple
Hollow-end mill fits in drill press, spot faces the front rivet to take off just the peened area. Often lets you re-peen the existing rivet and eliminate rebluing the receiver.
Ritaglia il Punta del Rivetto per Rendere Semplice la Rimozione della Molla Eiettore Rotta
Il fresatore a estremità cava si adatta al trapano a colonna, preparando la faccia del rivetto anteriore per rimuovere solo l'area peened. Spesso consente di ripristinare il rivetto esistente ed eliminare la necessità di ripristinare la finitura del ricevitore.
SPECIFICHE: Asta in acciaio, cutter in acciaio temprato. Lunghezza 2½" (6.3cm), diametro dell'asta .31" (7.8mm). Diametro del cutter .143" (3.6mm).
Altro...
Punteggi dei clienti per BROWNELLS REMINGTON 870 EJECTOR SPRING RIVET CUTTER
Numero di punteggi: 1
Da brownells.com: 1
Punteggio medio: 5
Great investment!(10.02.2016)
This little rivet cutter made me save over $200 in gunsmithing work on my old 870 Wingmaster, which had been sitting in the gun safe for years because of a ''too-expensive-to-replace'' broken ejector spring. The instructions provided with the tool are very clear and allowed me, as indicated, to re-use the rivet to lock the new spring into the ejector. The only thing I did differently than prescribed by the instructions was to drive the rivet cutter down on the tiny rivet head by hand instead of using a press drill. The rivet cutter being very sharp and the rivet metal being very soft, I was afraid to ruin the rivet using a press drill. It took me 10 minutes to cut the rivet head slowly and safely by hand (clockwise twist of the fingers with little pressure).