AR-15 USGI Barrel Nut Wrench with a 1/2 drive. Made of 4140 Chromoly Steel, Heat treated with a phosphate finish. Pins made of 8620 tool steel and tig welded in place.
Altro...
Chiave per dado del barilotto USGI AR-15 con attacco da 1/2. Realizzata in acciaio 4140 Chromoly, trattata termicamente con finitura fosfatata. I perni sono realizzati in acciaio per utensili 8620 e saldati a tig in posizione.
Altro...
Punteggi dei clienti per SPIKES TACTICAL 7-PIN USGI BARREL NUT WRENCH 1/2 DRIVE
Numero di punteggi: 2
Da brownells.com: 2
Punteggio medio: 4.5
GREAT TOOL BUT BROKE!(01.03.2015)
I finally bought this tool after years of using the standard type of AR wrenches for barrel change. It had come highly recommended by several friends. The tool worked wonderfully. It was far superior to any barrel tool I had used. It made barrel changes a snap. But, the tool failed after only a few builds. Two pins sheared off. I had the torque wrench set for 50lbs. I am sending it back and I am sure Brownell's will send a replacement. I will update review after using that tool.
(On Order) Not a review just a concern(18.10.2015)
One consideration while using this tool in conjunction with a torque wrench...
it will ONLY read correctly per the torque wrench value or setting IF the tool is 90 degrees to the torque wrench beam thereby maintaining the combined total length of the tool. If the tool is used at zero degrees (meaning it's an extension of the torque wrench), thereby increasing the combined total length of the tool, the torque value would have to be recalculated and reduced the appropriate amount. The center-line of the square drive to the center-line of the barrel nut wrench would have to be known first.
N. prodotto: 100014395 SPIKES TACTICAL 7-PIN USGI BARREL NUT WRENCH 1/2 DRIVE Parti Fabbricante: SAT1010815648020705 Chiave per dado del barilotto USGI AR-15 con attacco da 1/2. Realizzata in acciaio 4140 Chromoly, trattata termicamente con finitura fosfatata. I perni sono realizzati in acciaio per utensili 8620 e saldati a tig in posizione.
84.9CHF1CHF 84.90
*
Tempi di consegna circa 8-15 giorni dal magazzino negli Stati Uniti.
Adatto per:
AR-15
Peso della spedizione: 0.204kgAltezza di spedizione: 15mmLarghezza di spedizione: 81mmLunghezza di spedizione: 157mm
UPC
: 815648020705
Dettagli dell'elemento
Made in Usa
Scopri la chiave per dado del barilotto USGI AR-15 di SPIKES TACTICAL! 🔧 Realizzata in acciaio 4140, è ideale per il tuo AR-15.
AR-15 USGI Barrel Nut Wrench with a 1/2 drive. Made of 4140 Chromoly Steel, Heat treated with a phosphate finish. Pins made of 8620 tool steel and tig welded in place.
Altro...
Chiave per dado del barilotto USGI AR-15 con attacco da 1/2. Realizzata in acciaio 4140 Chromoly, trattata termicamente con finitura fosfatata. I perni sono realizzati in acciaio per utensili 8620 e saldati a tig in posizione.
Altro...
Punteggi dei clienti per SPIKES TACTICAL 7-PIN USGI BARREL NUT WRENCH 1/2 DRIVE
Numero di punteggi: 2
Da brownells.com: 2
Punteggio medio: 4.5
GREAT TOOL BUT BROKE!(01.03.2015)
I finally bought this tool after years of using the standard type of AR wrenches for barrel change. It had come highly recommended by several friends. The tool worked wonderfully. It was far superior to any barrel tool I had used. It made barrel changes a snap. But, the tool failed after only a few builds. Two pins sheared off. I had the torque wrench set for 50lbs. I am sending it back and I am sure Brownell's will send a replacement. I will update review after using that tool.
(On Order) Not a review just a concern(18.10.2015)
One consideration while using this tool in conjunction with a torque wrench...
it will ONLY read correctly per the torque wrench value or setting IF the tool is 90 degrees to the torque wrench beam thereby maintaining the combined total length of the tool. If the tool is used at zero degrees (meaning it's an extension of the torque wrench), thereby increasing the combined total length of the tool, the torque value would have to be recalculated and reduced the appropriate amount. The center-line of the square drive to the center-line of the barrel nut wrench would have to be known first.