Il Carrello è vuoto.

Carrello

Aiuto e contatti

Spedizione gratuita con ordini superiori ad CHF 399

Politica di restituzione di 100 giorni

Newsletter

Offerte

Oltre 300.000 clienti - vi ringraziamo!

4,93/5 "Molto buono" (1400+ recensioni)

Oltre 40.000 prodotti per caccia e sport di tiro

SINCLAIR/L.E. WILSON
STAINLESS STEEL CASE TRIMMER KIT

749011888

L.E. Wilson Case Trimmer and Sinclair Mounting Stand with “SharkFin” Case Holder Clamp (order case holders separately.) This mounting stand and clamping attachment make case trimming much quicker and comfortable. The mounting stand can be C-clamped or permanently mounted to a bench top. The “SharkFin” Case Holder Clamp swings quickly into place and provides downward pressure on the case holder while trimming.

Altro...

Trimmer per casi L.E. Wilson e supporto di montaggio Sinclair con morsetto per portacase “SharkFin” (ordinare i portacase separatamente). Questo supporto di montaggio e l'attacco di serraggio rendono il trimmaggio dei casi molto più veloce e confortevole. Il supporto di montaggio può essere fissato con morsetti a C o montato permanentemente su un piano di lavoro. Il morsetto per portacase “SharkFin” si sposta rapidamente in posizione e fornisce pressione verso il basso sul portacase durante il trimmaggio.

Altro...

Punteggi dei clienti per SINCLAIR/L.E. WILSON STAINLESS TRIMMER WITH STAND & SHARK FIN CLAMP

Numero di punteggi: 7
Da brownells.com: 7
Punteggio medio: 3.7

Poor Finish (25.01.2011)

The finish was poor compared to the picture on the cover of my catalog. The base of the cutter was throughly pitted across the entire surface, a case holder was also lightly pitted. The cuts in the base to retain the two long thin rods had rough machining marks. The hole in the trimmer stand for the "sharkfin" still had metal burrs protruding which needed to be removed. The Sinclair case holder adapter had scuff marks from the two long thin rods which made it look like I was sent a used part. None of this was major enough to effect function, but due to the cost, it is somewhat disappointing.

one of its kind (27.03.2011)

the design is perfect but I wish they sell these from the start with the ergonomic crank handle.I fixed my problem by putting rubber on the handle so it won't hurt my hand.

Perfect out of the box! (20.04.2011)

This accessory is great. It assembled flawlessly and the shark fin required no adjustment to get rolling. It's a pleasure working with perfect tools.

Excellent (04.10.2011)

It's hard to beat Wilson tools of any kind, and this trimmer is no exception. I've had mine for about 2 years now, and it still functions flawlessly. This trimmer differs from all others in that it uses case holders and you'll need to purchase the specific one(s) for each caliber(s). This all but eliminates wobble, mis-alignment, etc., as the case is perfectly centered. I was reluctant to purchase this trimmer for this reason, but I'm glad I did.

Great Trimmer, No attaching screws? (24.08.2012)

The Wilson trimmer works great. It is easy to adjust and set up. It cuts square and to a consistent length. I only have one minor negative thing, that isn't a reflection of the trimmer. When I got mine it did not come with screws to attach the base to the trimmer. It was an easy fix, I had to get two hex head screws that are 10-32 thread pitch. I had to buy one inch long screws and cut them down to about .875 to get them to the proper length to attach the trimmer to the base. It would have been nice to have the screws included. Maybe I was just unlucky and they usually are, I don't know. That being said I would highly recommend it.

Difficult to adjust (11.09.2017)

When I got it, I was impressed with it, the construction quality is good and it looks nice. I read the instructions well and it seems straightforward in the instructions. It does cut the case mouths nice and square, I will give it that. Very very square. However, I have found it a poor case trimmer, because it is extremely difficult to set a repeatable case trim length. I will set it up for .223 Remington, for example at trim length of 1.750. Afterwards, case lengths will be all over the place. Its super sensitive to set up for case length and very sensitive to both how tight the set screw is as well as hand pressure on the handle while cranking it. I dont use it.

Problems 2 case (21.06.2018)

Very nice looking trimmer but on my second case the handle fell off the crank. I can't get it screwed back on because the handle and the screen I side it rotate separately of each other.

Leggi più recensioni su brownells.com

219.9 219.9 1 CHF

N. prodotto: 749011888
SINCLAIR/L.E. WILSON STAINLESS TRIMMER WITH STAND & SHARK FIN CLAMP Trimmer per casi L.E. Wilson e supporto di montaggio Sinclair con morsetto per portacase “SharkFin” (ordinare i portacase separatamente). Questo supporto di montaggio e l'attacco di serraggio rendono il trimmaggio dei casi molto più veloce e confortevole. Il supporto di montaggio può essere fissato con morsetti a C o montato permanentemente su un piano di lavoro. Il morsetto per portacase “SharkFin” si sposta rapidamente in posizione e fornisce pressione verso il basso sul portacase durante il trimmaggio.

219.9 CHF 3 CHF 219.90 *

Tempi di consegna circa 8-15 giorni dal magazzino negli Stati Uniti.

Aggiungi alla lista degli acquisti

Domande

Dettagli

Aggiungi alla lista degli acquisti

Domande

Top takeaways

Trimmer per bossoli L.E. Wilson con supporto di montaggio Sinclair e morsetto "SharkFin".
Il supporto di montaggio può essere fissato con un morsetto a C o montato permanentemente.
Il morsetto "SharkFin" si posiziona rapidamente e fornisce pressione verso il basso durante il trimmaggio.

Caratteristiche

Peso della spedizione: 0.975kg Altezza di spedizione: 102mm Larghezza di spedizione: 127mm Lunghezza di spedizione: 191mm

Dettagli dell'elemento

Made in Usa

Scopri il kit trimmer in acciaio inox Sinclair/L.E. Wilson con supporto e morsetto SharkFin 🦈. Rendi il trimmaggio dei casi veloce e semplice!

Altro...

Punteggi dei clienti per SINCLAIR/L.E. WILSON STAINLESS TRIMMER WITH STAND & SHARK FIN CLAMP

Numero di punteggi: 7
Da brownells.com: 7
Punteggio medio: 3.7

Poor Finish (25.01.2011)

one of its kind (27.03.2011)

the design is perfect but I wish they sell these from the start with the ergonomic crank handle.I fixed my problem by putting rubber on the handle so it won't hurt my hand.

Perfect out of the box! (20.04.2011)

This accessory is great. It assembled flawlessly and the shark fin required no adjustment to get rolling. It's a pleasure working with perfect tools.

Excellent (04.10.2011)

Great Trimmer, No attaching screws? (24.08.2012)

Difficult to adjust (11.09.2017)

Problems 2 case (21.06.2018)

Very nice looking trimmer but on my second case the handle fell off the crank. I can't get it screwed back on because the handle and the screen I side it rotate separately of each other.

Leggi più recensioni su brownells.com