Great for short stroke cleaning applications when using J-B Bore Cleaner and other paste type cleaners. The stops prevent patches from coming out at the muzzle. Many shooters use them when treating a barrel with a bore conditioner. Three sizes available to fit Dewey and most other cleaning rods. Small stop fits 22-6.5mm caliber rods and the X-Large stops fits 35 caliber rods.
Altro...
Ottimo per applicazioni di pulizia a corsa corta quando si utilizza J-B Bore Cleaner e altri detergenti in pasta. I fermapatch impediscono ai pezzi di uscire dalla volata. Molti tiratori li usano quando trattano un'anima con un condizionatore per canne. Disponibili tre misure per adattarsi alle canne Dewey e alla maggior parte degli altri bastoni di pulizia. Il fermo piccolo si adatta a canne di calibro 22-6,5 mm e il fermo X-Large si adatta a canne di calibro 35.
Altro...
Punteggi dei clienti per SINCLAIR INTERNATIONAL CLEANING ROD STOP - SMALL
Numero di punteggi: 2
Da brownells.com: 2
Punteggio medio: 3
Not as helpful as I had hoped(18.10.2014)
I bought the cleaning rod stops about a year or so ago for use with my Dewey 36" 22LR sized cleaning rod to clean my slide action and semi auto rimfire rifles. They're very easy to install, but the problem I've had is being able to keep them from sliding backwards instead of stopping against the muzzle when pushing a tight jag or bronze brush through the bore. These stops are handsomely constructed but it appears the nylon thumb screw just doesn't have enough bite to keep the stop from moving backwards when it's pushed against the muzzle with more than a little force. To counteract this movement I've resorted to cutting a half inch wide strip of duck tape and wrapping it around the rod with around 8 layers just behind where I want to set the stop. This has been helpful in preventing the stop from sliding backwards, especially when using a new and very tight fitting bore brush. Otherwise, I'm still glad I bought them because they're much better than using drill bit stops or trying to eyeball a witness mark on the rod to keep from banging the bronze brush against the bolt face of a Remington Model 12 and similar closed receivers. And I'd still recommend them to a friend with full disclosure of my experience with them, or until a better design comes to market.
Works great on Tipton Cleaning rod.(30.10.2014)
I read the one poor review and still decided to take the risk. I am glad I did. I installed the 30 cal stop on my 30 Cal Tipton Cleaning rod. At first, it did slide a bit when I first used it in my M1 Garand. I then used a little more twist on the set screw. After that, I had no issues. In fact, I was so happy with it that I just ordered 4 more 20 cal stops for my 3 other cleaning rods and one for a friend. I have since used the 30 cal stop in my S&W revolver, 357 lever, and 30-30 lever. One thing to keep in mind... It works GREAT once the length is set right. But be careful you don't set it with the bolt open then close bolt and try to use it. Obviously that won't work. ;)
N. prodotto: 749000267 SINCLAIR INTERNATIONAL CLEANING ROD STOP - SMALL Parti Fabbricante: 02-1000 Ottimo per applicazioni di pulizia a corsa corta quando si utilizza J-B Bore Cleaner e altri detergenti in pasta. I fermapatch impediscono ai pezzi di uscire dalla volata. Molti tiratori li usano quando trattano un'anima con un condizionatore per canne. Disponibili tre misure per adattarsi alle canne Dewey e alla maggior parte degli altri bastoni di pulizia. Il fermo piccolo si adatta a canne di calibro 22-6,5 mm e il fermo X-Large si adatta a canne di calibro 35.
14.9CHF0CHF 14.90
*
In arretrato, tempi di consegna circa 4-12 settimane dal magazzino negli Stati Uniti.
Great for short stroke cleaning applications when using J-B Bore Cleaner and other paste type cleaners. The stops prevent patches from coming out at the muzzle. Many shooters use them when treating a barrel with a bore conditioner. Three sizes available to fit Dewey and most other cleaning rods. Small stop fits 22-6.5mm caliber rods and the X-Large stops fits 35 caliber rods.
Altro...
Ottimo per applicazioni di pulizia a corsa corta quando si utilizza J-B Bore Cleaner e altri detergenti in pasta. I fermapatch impediscono ai pezzi di uscire dalla volata. Molti tiratori li usano quando trattano un'anima con un condizionatore per canne. Disponibili tre misure per adattarsi alle canne Dewey e alla maggior parte degli altri bastoni di pulizia. Il fermo piccolo si adatta a canne di calibro 22-6,5 mm e il fermo X-Large si adatta a canne di calibro 35.
Altro...
Punteggi dei clienti per SINCLAIR INTERNATIONAL CLEANING ROD STOP - SMALL
Numero di punteggi: 2
Da brownells.com: 2
Punteggio medio: 3
Not as helpful as I had hoped(18.10.2014)
I bought the cleaning rod stops about a year or so ago for use with my Dewey 36" 22LR sized cleaning rod to clean my slide action and semi auto rimfire rifles. They're very easy to install, but the problem I've had is being able to keep them from sliding backwards instead of stopping against the muzzle when pushing a tight jag or bronze brush through the bore. These stops are handsomely constructed but it appears the nylon thumb screw just doesn't have enough bite to keep the stop from moving backwards when it's pushed against the muzzle with more than a little force. To counteract this movement I've resorted to cutting a half inch wide strip of duck tape and wrapping it around the rod with around 8 layers just behind where I want to set the stop. This has been helpful in preventing the stop from sliding backwards, especially when using a new and very tight fitting bore brush. Otherwise, I'm still glad I bought them because they're much better than using drill bit stops or trying to eyeball a witness mark on the rod to keep from banging the bronze brush against the bolt face of a Remington Model 12 and similar closed receivers. And I'd still recommend them to a friend with full disclosure of my experience with them, or until a better design comes to market.
Works great on Tipton Cleaning rod.(30.10.2014)
I read the one poor review and still decided to take the risk. I am glad I did. I installed the 30 cal stop on my 30 Cal Tipton Cleaning rod. At first, it did slide a bit when I first used it in my M1 Garand. I then used a little more twist on the set screw. After that, I had no issues. In fact, I was so happy with it that I just ordered 4 more 20 cal stops for my 3 other cleaning rods and one for a friend. I have since used the 30 cal stop in my S&W revolver, 357 lever, and 30-30 lever. One thing to keep in mind... It works GREAT once the length is set right. But be careful you don't set it with the bolt open then close bolt and try to use it. Obviously that won't work. ;)