Lets you use your entire hand to grip the gun for better recoil control and more consistent shot placement. Extended “shelf” for the little finger attaches in place of the factory magazine base. Makes shooting these little “handfuls” a lot more comfortable.
SPECS: Impact-resistant plastic, black.
Altro...
Aggiunge Controllo del Rinculo per una Maggiore Precisione
Ti consente di utilizzare tutta la mano per impugnare l'arma, migliorando il controllo del rinculo e garantendo una maggiore coerenza nel posizionamento dei colpi. La "shelf" estesa per il mignolo si attacca al posto della base del caricatore di fabbrica. Rende il tiro con queste piccole "maniglie" molto più confortevole.
SPECIFICHE: Plastica resistente agli urti, nera.
Altro...
Punteggi dei clienti per PEARCE GRIP FITS GLOCK® 30, ADDS 0
Numero di punteggi: 18
Da brownells.com: 16
Punteggio medio: 4.1
Good looking but cheap plastic(06.04.2021)
I've bought two +2 extension for my glock 17. They look very good on the mag, have a great grip to check if the mag is well set in the gun.
But after three afternoons of training, so after around 800 rounds, the two extensions fell apart and opened the magazines with the rounds falling on the ground... I've never overfilled the magazines. They are 17+2 mag but always put a max of 17 rounds.
Great looking piece to show off but not the quality to really use them.
Plus One Extension(24.12.2015)
This product works great! No feed problems at all ball or hollow point. Gives you one more round capacity without changing the profile. Gives the 43 a full grip feel. Worth the money!
Excellent item for magazine(19.05.2016)
Perfect fit and function with 1 added round. Smooth edges keep it snag free and CCW friendly.
Can't rely on it.(04.10.2017)
I found that with hollow points I would get failure to feeds occasionally. Federal HST 124+p and some practice, non expanding, hollow point reloads I got at a gun show 124 gn. Sometimes the slide would miss the casing or slip off (pictured). Other times (with the practice stuff) it would jam against the bottom of the feed ramp. Basically plenty of evidence that the magazine spring tension is not keeping up with the recoil spring.
Maybe my gun is too new and the recoil spring needs to break in a little bit but I'm not going to find out.
Can't rely on it.(08.10.2017)
I found that with hollow points I would get failure to feeds occasionally. Federal HST 124+p and some practice, non expanding, hollow point reloads I got at a gun show 124 gn. Sometimes the slide would miss the casing or slip off (pictured). Other times (with the practice stuff) it would jam against the bottom of the feed ramp. Basically plenty of evidence that the magazine spring tension is not keeping up with the recoil spring. Maybe my gun is too new and the recoil spring needs to break in a little bit but I'm not going to find out.
I have these on both of my Glock 42 mags. I love them because now I can get my entire hand on the mini Glock, no pinky left wanting. They are well worth the cost! On the other hand, I bought the 42 to pocket carry and despite what everyone seems to think. I had no problems doing this, until I installed these grip extensions. The 42 will still carry in the pocket of my cargo shorts and pants but my jean pockets are just to tight. I solved this by buying a Desantis Intruder (which is a great holster by the way) but it somewhat defeats the purpose of what I bought the gun for. Overall, they're worth it. If you carry on the hip BUY THEM if you prefer pocket carry, give them a shot you'll only be out 20 bucks.
Needs modification to fit +2 9mm(04.02.2014)
Fits very well and easy to install. The hard part is getting the base plate off a new Gen 4 mag: Big vice-grips helped a lot there. Installed properly, there's NO way to fit +2 in there because the insert does not seat. Trim 1/16" to 1/8" off the front of the insert (the narrow end). It will seat properly and 12 rounds will fit. Tight fit, but they'll fit.
+2 for G26(10.02.2015)
+3 is asking a lot out of this extension. That 13th round took everything I had with a loader to get it in the magazine. Once in, it was very tight, although I don't thing the slide would have any issues chambering the first round. Adding that last round by hand was impossible. It looks stock and feels great. I have a sense of extra control just from gripping the weapon. I can't wait to test it on the range. I will update if necessary.
I replaced the base pad on one of my stock mags with the Zero Extension and immediately had to order several more for my other mags. These are great, they extend the mag enough that you have a better grip and control of the weapon, yet in no way make the weapon more visable for carry purposes.
Wow! Hard to find this item else where!(06.01.2016)
My hands are a bit bigger than average. This magazine/grip extension really helps with the Glock 36. Thanks Brownell's!
Excellent Extender(25.09.2012)
These Pearce extenders fit the mags to my compact G19 perfectly and go on easily. They provide that all-important extension to the 19 grip to comfortably give the pinky a solid rest. Appearance-wise, they are well made, look well-made, and tie into the profile of the G19 perfectly. They also fit the full size glock mags but of course are not as necessary given the longer grip.
Necessary for the Glock 30(24.09.2009)
This small inexpensive part makes the Glock 30 manageable. Without it, it is almost impossible to achieve a reasonable grip. Because the stock grip is so fat (double stack .45), there is little room for the small finger. This Pearce part makes the pistol comfortable and controllable. It is unknown why Glock does not make this magazine with a similar extension. The Pearce extension makes all the difference. Do not shoot without it.
Must Have(02.01.2010)
This mag extension is a must have for controlling your G29. The extension gives a full hand grip for far better recoil control and faster follow up shots. The extension adds very little length to the magazine making it easy to carry extra mags.
Best for Glock 26, too(23.02.2015)
This is the best magazine extension to use on the Glock 26 9mm despite what the description reads. It perfectly matches the appearance and size of the finger grooves on the Glock 26 frame, and looks like a factory piece. It really only allows one additional 9mm round to be loaded, though, but greatly enhances the grip and doesn't detract from conceal-ability. Carry a G17 magazine for a spare and you'll have 11+1+17=29 rounds on you!
Broke first time out.(02.05.2010)
Gave great grip extension to my Glock 26, however I accidentally dropped an empty magazine on a wood floor and the base broke off. Would not use for concealed carry!
Pearce Grip Extension for Glock 26/27(21.01.2011)
Don't bother with the installation instructions which say to push in the retention button while squeezing the magazine with your fingers while sliding off the magazine floor plate. You would need three hands and one of them better have super-human strength. I have a strong grip and couldn't come close to releasing the retention tabs. Simply use a couple of jewelers screw drivers to carefully pry the floor plate off the retention lips. This can be done without damaging the magazine or the original floor plate. Once you get the old floor plate off, installation of the Pearce extension just takes seconds. I would have given this 5 stars if the installation instructions had been better.
Great addition to my Glock(10.05.2012)
Gives you good control and allows a home for your pinky which was an issue with my Glock 26
N. prodotto: 092100030 PEARCE GRIP FITS GLOCK® 30, ADDS 0 Parti Fabbricante: PG-30605849200309 Ti consente di utilizzare tutta la mano per impugnare l'arma, migliorando il controllo del rinculo e garantendo una maggiore coerenza nel posizionamento dei colpi. La "shelf" estesa per il mignolo si attacca al posto della base del caricatore di fabbrica. Rende il tiro con queste piccole "maniglie" molto più confortevole.
24.9CHF118CHF 24.90
*
Tempi di consegna circa 8-15 giorni dal magazzino negli Stati Uniti.
Consente di utilizzare tutta la mano per un migliore controllo del rinculo.
La "mensola" estesa per il mignolo si fissa al posto della base del caricatore di fabbrica.
Rende il tiro più confortevole con queste piccole "maniglie".
Caratteristiche
Adatto per:
Glock
Modello:
30
Tipo:
Grip Extenders
Peso della spedizione: 0.02kgAltezza di spedizione: 28mmLarghezza di spedizione: 69mmLunghezza di spedizione: 89mm
UPC
: 605849200309
Dettagli dell'elemento
Made in Usa
Classificazione per l'export dagli US: 0A501.x
Questi articoli sono controllati dal governo degli Stati Uniti e ne è autorizzata l'esportazione solo nel paese di destinazione finale e l'uso solo da parte del destinatario finale o degli utenti finali qui identificati. Questi beni non possono essere rivenduti, trasferiti o altrimenti ceduti a nessun altro paese o a persone diverse dal destinatario finale o dall'utente finale autorizzati, nella loro forma originale o dopo essere stati incorporati in altri articoli, senza prima ottenere l'approvazione dal governo degli Stati Uniti o come altrimenti autorizzato dalla legge e dai regolamenti degli Stati Uniti.
This item is controlled by the U.S. government and authorized for export only to the country of ultimate destination for use by the ultimate consignee or end-user(s) herein identified. It may not be resold, transferred, or otherwise disposed of, to any other country or to any person other than the authorized ultimate consignee or end-user(s), either in their original form or after being incorporated into other items, without first obtaining approval from the U.S. government or as otherwise authorized by U.S. law and regulations.
N. prodotto: 092100029 PEARCE GRIP FITS GLOCK® 29, ADDS 0 Parti Fabbricante: PG-29605849200293 Ti consente di utilizzare tutta la mano per impugnare l'arma, migliorando il controllo del rinculo e garantendo una maggiore coerenza nel posizionamento dei colpi. La "shelf" estesa per il mignolo si attacca al posto della base del caricatore di fabbrica. Rende il tiro con queste piccole "maniglie" molto più confortevole.
14.9CHF19CHF 14.90
*
Tempi di consegna circa 8-15 giorni dal magazzino negli Stati Uniti.
N. prodotto: 092000005 PEARCE GRIP FITS GLOCK® MID-/FULL-SIZE, ADDS 0 Parti Fabbricante: PG-19605849200231 Ti consente di utilizzare tutta la mano per impugnare l'arma, migliorando il controllo del rinculo e garantendo una maggiore coerenza nel posizionamento dei colpi. La "shelf" estesa per il mignolo si attacca al posto della base del caricatore di fabbrica. Rende il tiro con queste piccole "maniglie" molto più confortevole.
24.9CHF10CHF 24.90
*
Tempi di consegna circa 8-15 giorni dal magazzino negli Stati Uniti.
N. prodotto: 092000008 PEARCE GRIP FITS GLOCK® 36 PLUS 0, ADDS 0 Parti Fabbricante: PG-360605849200453 Ti consente di utilizzare tutta la mano per impugnare l'arma, migliorando il controllo del rinculo e garantendo una maggiore coerenza nel posizionamento dei colpi. La "shelf" estesa per il mignolo si attacca al posto della base del caricatore di fabbrica. Rende il tiro con queste piccole "maniglie" molto più confortevole.
24.9CHF13CHF 24.90
*
Tempi di consegna circa 8-15 giorni dal magazzino negli Stati Uniti.
N. prodotto: 100002618 PEARCE GRIP FITS GLOCK® MID/FULL HI-CAP, +2 TO 9MM/.40/357; +1 .45GAP Parti Fabbricante: PGGP605849200385 Ti consente di utilizzare tutta la mano per impugnare l'arma, migliorando il controllo del rinculo e garantendo una maggiore coerenza nel posizionamento dei colpi. La "shelf" estesa per il mignolo si attacca al posto della base del caricatore di fabbrica. Rende il tiro con queste piccole "maniglie" molto più confortevole.
14.9CHF82CHF 14.90
*
Tempi di consegna circa 8-15 giorni dal magazzino negli Stati Uniti.
N. prodotto: 100002617 PEARCE GRIP FITS GLOCK® 26/27/33/39, ADDS 0 Parti Fabbricante: PG-26XL605849200330 Ti consente di utilizzare tutta la mano per impugnare l'arma, migliorando il controllo del rinculo e garantendo una maggiore coerenza nel posizionamento dei colpi. La "shelf" estesa per il mignolo si attacca al posto della base del caricatore di fabbrica. Rende il tiro con queste piccole "maniglie" molto più confortevole.
24.9CHF4CHF 24.90
*
Tempi di consegna circa 8-15 giorni dal magazzino negli Stati Uniti.
N. prodotto: 092000026 PEARCE GRIP FITS GLOCK® GEN 4/5 26/27/33/39, ADDS 0 Parti Fabbricante: PG-26G4605849200415 Ti consente di utilizzare tutta la mano per impugnare l'arma, migliorando il controllo del rinculo e garantendo una maggiore coerenza nel posizionamento dei colpi. La "shelf" estesa per il mignolo si attacca al posto della base del caricatore di fabbrica. Rende il tiro con queste piccole "maniglie" molto più confortevole.
14.9CHF9CHF 14.90
*
Tempi di consegna circa 8-15 giorni dal magazzino negli Stati Uniti.
N. prodotto: 092000029 PEARCE GRIP FITS GLOCK® 42 GRIP EXTENSION, ADDS 0 Parti Fabbricante: PG-42605849200422 Ti consente di utilizzare tutta la mano per impugnare l'arma, migliorando il controllo del rinculo e garantendo una maggiore coerenza nel posizionamento dei colpi. La "shelf" estesa per il mignolo si attacca al posto della base del caricatore di fabbrica. Rende il tiro con queste piccole "maniglie" molto più confortevole.
24.9CHF7CHF 24.90
*
Tempi di consegna circa 8-15 giorni dal magazzino negli Stati Uniti.
N. prodotto: 092000034 PEARCE GRIP GLOCK 43 PLUS 1 GRIP EXTENSION Parti Fabbricante: PG-43+1605849200477 Ti consente di utilizzare tutta la mano per impugnare l'arma, migliorando il controllo del rinculo e garantendo una maggiore coerenza nel posizionamento dei colpi. La "shelf" estesa per il mignolo si attacca al posto della base del caricatore di fabbrica. Rende il tiro con queste piccole "maniglie" molto più confortevole.
14.9CHF19CHF 14.90
*
Tempi di consegna circa 8-15 giorni dal magazzino negli Stati Uniti.
N. prodotto: 092000035 PEARCE GRIP FITS GLOCK® GEN 4/5 26/27/33, ADDS 2 9MM, ADDES 1 40/357 Parti Fabbricante: PG-G42733605849200460 Ti consente di utilizzare tutta la mano per impugnare l'arma, migliorando il controllo del rinculo e garantendo una maggiore coerenza nel posizionamento dei colpi. La "shelf" estesa per il mignolo si attacca al posto della base del caricatore di fabbrica. Rende il tiro con queste piccole "maniglie" molto più confortevole.
25.9CHF13CHF 25.90
*
Tempi di consegna circa 8-15 giorni dal magazzino negli Stati Uniti.
N. prodotto: 092100027 PEARCE GRIP FITS GLOCK® 27/33, ADDS 1 Parti Fabbricante: PG-2733605849200279 Ti consente di utilizzare tutta la mano per impugnare l'arma, migliorando il controllo del rinculo e garantendo una maggiore coerenza nel posizionamento dei colpi. La "shelf" estesa per il mignolo si attacca al posto della base del caricatore di fabbrica. Rende il tiro con queste piccole "maniglie" molto più confortevole.
Lets you use your entire hand to grip the gun for better recoil control and more consistent shot placement. Extended “shelf” for the little finger attaches in place of the factory magazine base. Makes shooting these little “handfuls” a lot more comfortable.
SPECS: Impact-resistant plastic, black.
Altro...
Aggiunge Controllo del Rinculo per una Maggiore Precisione
Ti consente di utilizzare tutta la mano per impugnare l'arma, migliorando il controllo del rinculo e garantendo una maggiore coerenza nel posizionamento dei colpi. La "shelf" estesa per il mignolo si attacca al posto della base del caricatore di fabbrica. Rende il tiro con queste piccole "maniglie" molto più confortevole.
SPECIFICHE: Plastica resistente agli urti, nera.
Altro...
Punteggi dei clienti per PEARCE GRIP FITS GLOCK® 30, ADDS 0
Numero di punteggi: 18
Da brownells.com: 16
Punteggio medio: 4.1
Good looking but cheap plastic(06.04.2021)
I've bought two +2 extension for my glock 17. They look very good on the mag, have a great grip to check if the mag is well set in the gun.
But after three afternoons of training, so after around 800 rounds, the two extensions fell apart and opened the magazines with the rounds falling on the ground... I've never overfilled the magazines. They are 17+2 mag but always put a max of 17 rounds.
Great looking piece to show off but not the quality to really use them.
Plus One Extension(24.12.2015)
This product works great! No feed problems at all ball or hollow point. Gives you one more round capacity without changing the profile. Gives the 43 a full grip feel. Worth the money!
Excellent item for magazine(19.05.2016)
Perfect fit and function with 1 added round. Smooth edges keep it snag free and CCW friendly.
Can't rely on it.(04.10.2017)
I found that with hollow points I would get failure to feeds occasionally. Federal HST 124+p and some practice, non expanding, hollow point reloads I got at a gun show 124 gn. Sometimes the slide would miss the casing or slip off (pictured). Other times (with the practice stuff) it would jam against the bottom of the feed ramp. Basically plenty of evidence that the magazine spring tension is not keeping up with the recoil spring.
Maybe my gun is too new and the recoil spring needs to break in a little bit but I'm not going to find out.
Can't rely on it.(08.10.2017)
I found that with hollow points I would get failure to feeds occasionally. Federal HST 124+p and some practice, non expanding, hollow point reloads I got at a gun show 124 gn. Sometimes the slide would miss the casing or slip off (pictured). Other times (with the practice stuff) it would jam against the bottom of the feed ramp. Basically plenty of evidence that the magazine spring tension is not keeping up with the recoil spring. Maybe my gun is too new and the recoil spring needs to break in a little bit but I'm not going to find out.
I have these on both of my Glock 42 mags. I love them because now I can get my entire hand on the mini Glock, no pinky left wanting. They are well worth the cost! On the other hand, I bought the 42 to pocket carry and despite what everyone seems to think. I had no problems doing this, until I installed these grip extensions. The 42 will still carry in the pocket of my cargo shorts and pants but my jean pockets are just to tight. I solved this by buying a Desantis Intruder (which is a great holster by the way) but it somewhat defeats the purpose of what I bought the gun for. Overall, they're worth it. If you carry on the hip BUY THEM if you prefer pocket carry, give them a shot you'll only be out 20 bucks.
Needs modification to fit +2 9mm(04.02.2014)
Fits very well and easy to install. The hard part is getting the base plate off a new Gen 4 mag: Big vice-grips helped a lot there. Installed properly, there's NO way to fit +2 in there because the insert does not seat. Trim 1/16" to 1/8" off the front of the insert (the narrow end). It will seat properly and 12 rounds will fit. Tight fit, but they'll fit.
+2 for G26(10.02.2015)
+3 is asking a lot out of this extension. That 13th round took everything I had with a loader to get it in the magazine. Once in, it was very tight, although I don't thing the slide would have any issues chambering the first round. Adding that last round by hand was impossible. It looks stock and feels great. I have a sense of extra control just from gripping the weapon. I can't wait to test it on the range. I will update if necessary.
I replaced the base pad on one of my stock mags with the Zero Extension and immediately had to order several more for my other mags. These are great, they extend the mag enough that you have a better grip and control of the weapon, yet in no way make the weapon more visable for carry purposes.
Wow! Hard to find this item else where!(06.01.2016)
My hands are a bit bigger than average. This magazine/grip extension really helps with the Glock 36. Thanks Brownell's!
Excellent Extender(25.09.2012)
These Pearce extenders fit the mags to my compact G19 perfectly and go on easily. They provide that all-important extension to the 19 grip to comfortably give the pinky a solid rest. Appearance-wise, they are well made, look well-made, and tie into the profile of the G19 perfectly. They also fit the full size glock mags but of course are not as necessary given the longer grip.
Necessary for the Glock 30(24.09.2009)
This small inexpensive part makes the Glock 30 manageable. Without it, it is almost impossible to achieve a reasonable grip. Because the stock grip is so fat (double stack .45), there is little room for the small finger. This Pearce part makes the pistol comfortable and controllable. It is unknown why Glock does not make this magazine with a similar extension. The Pearce extension makes all the difference. Do not shoot without it.
Must Have(02.01.2010)
This mag extension is a must have for controlling your G29. The extension gives a full hand grip for far better recoil control and faster follow up shots. The extension adds very little length to the magazine making it easy to carry extra mags.
Best for Glock 26, too(23.02.2015)
This is the best magazine extension to use on the Glock 26 9mm despite what the description reads. It perfectly matches the appearance and size of the finger grooves on the Glock 26 frame, and looks like a factory piece. It really only allows one additional 9mm round to be loaded, though, but greatly enhances the grip and doesn't detract from conceal-ability. Carry a G17 magazine for a spare and you'll have 11+1+17=29 rounds on you!
Broke first time out.(02.05.2010)
Gave great grip extension to my Glock 26, however I accidentally dropped an empty magazine on a wood floor and the base broke off. Would not use for concealed carry!
Pearce Grip Extension for Glock 26/27(21.01.2011)
Don't bother with the installation instructions which say to push in the retention button while squeezing the magazine with your fingers while sliding off the magazine floor plate. You would need three hands and one of them better have super-human strength. I have a strong grip and couldn't come close to releasing the retention tabs. Simply use a couple of jewelers screw drivers to carefully pry the floor plate off the retention lips. This can be done without damaging the magazine or the original floor plate. Once you get the old floor plate off, installation of the Pearce extension just takes seconds. I would have given this 5 stars if the installation instructions had been better.
Great addition to my Glock(10.05.2012)
Gives you good control and allows a home for your pinky which was an issue with my Glock 26